Production organisations

1. An organisation responsible for the manufacture of products, parts and appliances shall demonstrate its capability in accordance with the provisions of Annex I (Part 21). This demonstration of capability is not required for the parts or appliances that an organisation manufactures which, in accordance with the provisions of Annex I (Part 21), are eligible for installation in a type-certified product without the need to be accompanied by an authorised release certificate (i.e. EASA Form 1).

2. By way of derogation from point 1, a manufacturer whose principal place of business is in a non-member State may demonstrate its capability by holding a certificate issued by that State for the product, part and appliance for which it applies, provided:

that State is the State of manufacture; and

the Agency has determined that the system of that State includes the same independent level of checking of compliance as provided by this Regulation, either through an equivalent system of approvals of organisations or through direct involvement of the competent authority of that State.

3. Production organisation approvals issued or recognised by a Member State in accordance with the JAA requirements and procedures and valid before 28 September 2003 shall be deemed to comply with this Regulation.

4. By way of derogation from paragraph 1, the production organisation may apply to the competent authority for exemptions from the environmental protection requirements referred to in the first subparagraph of Article 9(2) of Regulation (EU) 2018/1139.

5. By way of derogation from points 21.B.225(d)(1) and (2) of Annex I (Part 21), a production organisation that holds a valid approval certificate issued in accordance with Annex I (Part 21) may correct, until 7 March 2025, any findings of non-compliance related to the Annex I requirements introduced by Commission Delegated Regulation (EU) 2022/201 ( *1 ) .

Where after 7 March 2025 the organisation has not closed those findings, the approval certificate shall be revoked, limited or suspended in whole or in part.

6. By way of derogation from point 21.A.125C(a)(1) of Annex I (Part 21), an organisation that produces products, parts or appliances without an approval certificate and that holds a valid letter of agreement issued on or before 7 March 2023 in accordance with Annex I (Part 21) shall not be required to comply with the relevant Annex I requirements introduced by Delegated Regulation (EU) 2022/201.

7. By way of derogation from paragraph 1 of this Article, a natural or legal person whose principal place of business is in a Member State and who is responsible for the manufacture of products and their parts and appliances in accordance with Article 2(2) may alternatively demonstrate their capability in accordance with Annex Ib (Part 21 Light).

8. The demonstration of capability pursuant to paragraphs 1 or 2 shall not be required where the production organisation or natural or legal person are involved in the following manufacturing activities:

the manufacture of parts or appliances that are eligible, in accordance with Annex I (Part 21), for installation in a type-certified product without the need to be accompanied by an authorised release certificate (that is to say EASA Form 1);

the manufacture of parts that are eligible, in accordance with Annex Ib (Part 21 Light), for installation in an aircraft that has been subject to a declaration of design compliance without the need to be accompanied by an authorised release certificate (that is to say EASA Form 1);

the manufacture of an aircraft that has been subject to a declaration of design compliance referred to in Article 2(3), and of parts that are eligible for installation on such aircraft. In such case, the manufacturing activities shall be conducted in accordance with Subpart R of Section A of Annex Ib (Part 21 Light) by a production organisation or a natural or legal person whose principal place of business is in a Member State.

( *1 ) Commission Delegated Regulation (EU) 2022/201 of 10 December 2021 amending Regulation (EU) No 748/2012 as regards management systems and occurrence-reporting systems to be established by design and production organisations, as well as procedures applied by the Agency, and correcting that Regulation ( OJ L 33, 15.2.2022, p. 7 ).’."

COMMISSION DELEGATED REGULATION (EU) 2023/1028 of 20 March 2023 amending Regulation (EU) No 748/2012 as regards the definition of complex motor-powered aircraft and correcting that Regulation