Commission Implementing Regulation (EU) 2017/373 of 1 March 2017 laying down common requirements for providers of air traffic management/air navigation services and other air traffic management network functions and their oversight, repealing Regulation (EC) No 482/2008, Implementing Regulations (EU) No 1034/2011, (EU) No 1035/2011 and (EU) 2016/1377 and amending Regulation (EU) No 677/2011 (Text with EEA relevance. )
Annex IIIANNEX III
In force · version of Oct 4, 2026
COMMON REQUIREMENTS FOR ATM/ANS PROVIDERS
(Part-ATM/ANS.OR)
SUBPART A — GENERAL REQUIREMENTS (ATM/ANS.OR.A)
ATM/ANS.OR.A.001 Scope
In accordance with Article 6, this Annex establishes the requirements to be met by the service providers.
ATM/ANS.OR.A.005 Application for a service provider certificate
(a) Application for a service provider certificate or an amendment to an existing certificate shall be made in a form and manner established by the competent authority, taking into account the applicable requirements of this Regulation.
(b) In accordance with Article 6, in order to obtain the certificate, the service provider shall comply with: (1) the requirements referred to in Article 8b(1) of Regulation (EU) No 216/2008; (2) the common requirements set out in this Annex; (3) the specific requirements set out in Annexes IV to XIII, where those requirements are applicable in light of the services that the service provider provides or plans to provide.
ATM/ANS.OR.A.010 Application for a limited certificate
(a) Notwithstanding point (b), the air traffic services provider may apply for a certificate limited to the provision of services in the airspace under the responsibility of the Member State where its principal place of operation or, if any, registered office is located, when it provides or plans to provide services only with respect to one or more of the following categories: (1) aerial work; (2) general aviation; (3) commercial air transport limited to aircraft with less than 10 tonnes of maximum take-off mass or less than 20 passenger seats; (4) commercial air transport with less than 10 000 movements per year, regardless of the maximum take-off mass and the number of passenger seats; for the purposes of this provision, ‘movements’ means, in a given year, the average over the previous three years of the total number of take-offs and landings.
(b) In addition, the following air navigation service providers may also apply for a limited certificate: (1) an air navigation service provider, other than a provider of air traffic services, with a gross annual turnover of EUR 1 000 000 or less in relation to the services they provide or plan to provide; (2) an air navigation service provider providing aerodrome flight information services by operating regularly not more than one working position at any aerodrome.
(c) As determined by the competent authority, an air navigation service provider applying for a limited certificate in accordance with points (a) or (b)(1) shall comply, as a minimum, with the following requirements set out in: (1) point ATM/ANS.OR.B.001 Technical and operational competence and capability; (2) point ATM/ANS.OR.B.005 Management system; (3) point ATM/ANS.OR.B.020 Personnel requirements; (4) point ATM/ANS.OR.A.075 Open and transparent provision of services; (5) Annexes IV, V, VI and VIII, where those requirements are applicable in light of the services that the service provider provides or plans to provide, in accordance with Article 6.
(d) As determined by the competent authority, the air navigation service provider applying for a limited certificate in accordance with point (b)(2) shall comply, as a minimum, with the requirements set out in points (c)(1) to (c)(4) and with the specific requirements set out in Annex IV.
(e) An applicant for a limited certificate shall submit an application to the competent authority in a form and manner established by the competent authority.
ATM/ANS.OR.A.015 Declaration by flight information services providers
(a) Pursuant to Article 7, a flight information services provider may declare its capability and means of discharging the responsibilities associated with the services provided where it meets, in addition to the requirements referred to in Article 8b(1) of Regulation (EU) No 216/2008, the following alternative requirements: (1) the flight information services provider provides, or plans to provide, its services by operating regularly not more than one working position; (2) those services are of a temporary nature, for a duration agreed with the competent authority as necessary to ensure proportional safety assurance.
(b) A flight information services provider declaring its activities shall: (1) provide the competent authority with all the relevant information prior to commencing operations, in a form and manner established by the competent authority; (2) provide the competent authority with a list of the alternative means of compliance used, in accordance with point ATM/ANS.OR.A.020; (3) maintain compliance with the applicable requirements and with the information given in the declaration; (4) notify the competent authority of any changes to its declaration or the means of compliance it uses through submission of an amended declaration; (5) provide its services in accordance with its operations manual and comply with all the relevant provisions contained therein.
(c) Before ceasing the provision of its services, the flight information services provider declaring its activities shall notify the competent authority within a period determined by the competent authority.
(d) A flight information services provider declaring its activities shall comply with the following requirements set out in: (1) point ATM/ANS.OR.A.001 Scope; (2) point ATM/ANS.OR.A.020 Means of compliance; (3) point ATM/ANS.OR.A.035 Demonstration of compliance; (4) point ATM/ANS.OR.A.040 Changes — general; (5) point ATM/ANS.OR.A.045 Changes to the functional system; (6) point ATM/ANS.OR.A.050 Facilitation and cooperation; (7) point ATM/ANS.OR.A.055 Findings and corrective actions; (8) point ATM/ANS.OR.A.060 Immediate reaction to a safety problem; (9) point ATM/ANS.OR.A.065 Occurrence reporting; (10) point ATM/ANS.OR.B.001 Technical and operational competence and capability; (11) point ATM/ANS.OR.B.005 Management system; (12) point ATM/ANS.OR.B.020 Personnel requirements; (13) point ATM/ANS.OR.B.035 Operations manuals; (14) point ATM/ANS.OR.D.020 Liability and insurance cover, (15) Annex IV.
(e) A flight information services provider declaring its activities shall only start operation after receiving the acknowledgement of receipt of the declaration from the competent authority.
ATM/ANS.OR.A.020 Means of compliance
(a) Alternative means of compliance (AltMOC) to the AMC adopted by the Agency may be used by the service provider to establish compliance with the requirements of this Regulation.
(b) When the service provider wishes to use an AltMOC, it shall, prior to implementing it, provide the competent authority with a full description of the AltMOC. The description shall include any revisions to manuals or procedures that may be relevant, as well as an assessment demonstrating compliance with the requirements of this Regulation. A service provider may implement these alternative means of compliance subject to prior approval by the competent authority and upon receipt of the notification as prescribed in point ATM/ANS.AR.A.015(d).
ATM/ANS.OR.A.025 Continued validity of a certificate
(a) A service provider's certificate shall remain valid subject to: (1) the service provider remaining in compliance with the applicable requirements of this Regulation, including those concerning facilitating and cooperating for the purposes of the exercise of the powers of the competent authorities and those concerning the handling of findings as specified in points ATM/ANS.OR.A.050 and ATM/ANS.OR.A.055 respectively; (2) the certificate not having been surrendered, suspended or revoked.
(b) Upon revocation or surrender, the certificate shall be returned to the competent authority without delay.
ATM/ANS.OR.A.030 Continued validity of a declaration of a flight information services provider
A declaration made by the flight information services provider in accordance with point ATM/ANS.OR.A.015 shall remain valid subject to:
(a) the flight information services remaining in compliance with the applicable requirements of this Regulation, including those concerning facilitating and cooperating for the purposes of the exercise of the powers of the competent authorities and those concerning the handling of findings as specified in point ATM/ANS.OR.A.050 and ATM/ANS.OR.A.055 respectively;
(b) the declaration not having been withdrawn by the provider of such services or deregistered by the competent authority.
ATM/ANS.OR.A.035 Demonstration of compliance
A service provider shall provide all the relevant evidence to demonstrate compliance with the applicable requirements of this Regulation at the request of the competent authority.
ATM/ANS.OR.A.040 Changes — general
(a) The notification and management of: (1) a change to the functional system or a change that affects the functional system shall be carried out in accordance with point ATM/ANS.OR.A.045; (2) a change to the provision of service, the service provider's management system and/or safety management system, that does not affect the functional system, shall be carried out in accordance with point (b).
(b) Any change as referred to in point (a)(2) shall require prior approval before implementation, unless such a change is notified and managed in accordance with a procedure approved by the competent authority as laid down in point ATM/ANS.AR.C.025(c).
ATM/ANS.OR.A.045 Changes to a functional system
(a) A service provider planning a change to its functional system shall: (1) notify the competent authority of the change; (2) provide the competent authority, if requested, with any additional information that allows the competent authority to decide whether or not to review the argument for the change; (3) inform other service providers and, where feasible, aviation undertakings affected by the planned change.
(b) Having notified a change, the service provider shall inform the competent authority whenever the information provided in accordance with points (a)(1) and (2) is materially modified, and the relevant service providers and aviation undertakings whenever the information provided in accordance with point (a)(3) is materially modified.
(c) A service provider shall only allow the parts of the change, for which the activities required by the procedures referred to in point ATM/ANS.OR.B.010 have been completed, to enter into operational service.
(d) If the change is subject to competent authority review in accordance with point ATM/ANS.AR.C.035, the service provider shall only allow the parts of the change for which the competent authority has approved the argument to enter into operational service.
(e) When a change affects other service providers and/or aviation undertakings, as identified in point (a)(3), the service provider and these other service providers, in coordination, shall determine: (1) the dependencies with each other and, where feasible, with the affected aviation undertakings; (2) the assumptions and risk mitigations that relate to more than one service provider or aviation undertaking.
(f) Those service providers affected by the assumptions and risk mitigations referred to in point (e)(2) shall only use, in their argument for the change, agreed and aligned assumptions and risk mitigations with each other and, where feasible, with aviation undertakings.
(g) Before integrating ATM/ANS equipment into the functional system, the ATM/ANS provider shall ensure that: (1) new or modified ATM/ANS equipment is certified by the Agency in accordance with Delegated Regulation (EU) 2023/1768 and manufactured by an approved design or production organisation pursuant to Commission Implementing Regulation (EU) 2023/1769 ( 7 ); or (2) new or modified ATM/ANS equipment is declared by an approved design organisation pursuant to Delegated Regulation (EU) 2023/1768 and manufactured by an approved design or production organisation pursuant to Implementing Regulation (EU) 2023/1769; or (3) new or modified ATM/ANS equipment is issued with a statement of compliance in accordance with Article 6(1) of Delegated Regulation (EU) 2023/1768; or (4) when the ATM/ANS equipment is not subject to the conformity assessment under Delegated Regulation (EU) 2023/1768, the particular ATM/ANS equipment has been verified to comply with the applicable specifications and qualifications.
(h) The ATM/ANS provider shall ensure that the ATM/ANS equipment has been verified to comply with the equipment manufacturer’s specifications, including installation and on-site test(s).
(i) Before the ATM/ANS provider puts the ATM/ANS equipment into service, it shall ensure that the modified functional system integrating this ATM/ANS equipment meets all the applicable requirements and shall identify all deviations and limitations.
(j) When the ATM/ANS provider puts the ATM/ANS equipment into service, it shall ensure that the ATM/ANS equipment, or the modified one, is deployed according to the conditions of use, as well as to any applicable limitations, and meets all the applicable requirements.
ATM/ANS.OR.A.050 Facilitation and cooperation
A service provider shall facilitate inspections and audits by the competent authority or by a qualified entity acting on its behalf and it shall cooperate as necessary for the efficient and effective exercise of the powers of the competent authorities referred to in Article 5.
ATM/ANS.OR.A.055 Findings and corrective actions
After receipt of notification of findings from the competent authority, the service provider shall:
(a) identify the root cause of the non-compliance;
(b) define a corrective action plan that meets the approval by the competent authority;
(c) demonstrate corrective action implementation to the satisfaction of the competent authority within the time period proposed by the service provider and agreed with that authority, as defined in point ATM/ANS.AR.C.050(e).
ATM/ANS.OR.A.060 Immediate reaction to a safety problem
(a) A service provider shall implement any safety measures, including safety directives, mandated by the competent authority in accordance with point ATM/ANS.AR.A.025(c). When a safety directive is issued to correct the condition referred to in the statement of compliance issued in accordance with Article 6 of Delegated Regulation (EU) 2023/1768, the ATM/ANS provider shall, unless otherwise determined by the competent authority in case urgent action is needed: (1) propose appropriate corrective action and submit details of that proposal to the competent authority for approval; (2) following the approval by the competent authority, comply therewith.
ATM/ANS.OR.A.065 Occurrence reporting
(a) As part of its management system, the ATM/ANS provider shall establish and maintain an occurrence-reporting system, including mandatory and voluntary reporting. ATM/ANS providers established in a Member State shall ensure that the system complies with the requirements of Regulation (EU) No 376/2014 and Regulation (EU) 2018/1139, as well as with the delegated and implementing acts adopted on the basis of those regulations.
(b) The ATM/ANS provider shall report to the competent authority and to any other organisation required to be informed by the Member State, where the ATM/ANS provider provides its services, any safety-related event or condition that endangers or, if not corrected or addressed, could endanger an aircraft, its occupants or any other person, and in particular any accident or serious incident.
(c) Without prejudice to point (b), the ATM/ANS provider shall report to the competent authority and to the organisation responsible for the design and/or maintenance of the ATM/ANS systems and constituents, if different from the ATM/ANS provider, any malfunction, technical defect, exceedance of technical limitations, occurrence, or other irregular circumstance that has or may have endangered the safety of services and has not resulted in an accident or serious incident.
(d) Without prejudice to Regulation (EU) No 376/2014 and the delegated and implementing acts adopted on the basis thereof, reports shall: (1) be made as soon as practicable, but in any case within 72 hours after the ATM/ANS provider has become aware of the event or condition to which the report relates, unless exceptional circumstances prevent this; (2) be made in a form and manner established by the competent authority; (3) contain all pertinent information about the condition known to the ATM/ANS provider.
(e) For ATM/ANS providers that are not established in a Member State, initial mandatory reports shall: (1) appropriately safeguard the confidentiality of the identity of the reporter and of the persons mentioned in the report; (2) be made as soon as practicable, but in any case within 72 hours after the ATM/ANS provider has become aware of the occurrence, unless exceptional circumstances prevent this; (3) be made in a form and manner established by the competent authority; (4) contain all pertinent information about the condition known to the ATM/ANS provider.
(f) Without prejudice to Regulation (EU) No 376/2014 and its delegated and implementing acts, where relevant, a follow-up report providing details of actions the organisation intends to take to prevent similar occurrences in the future shall be made as soon as these actions have been identified; those follow-up reports shall: (1) be sent to the relevant entities initially reported to in accordance with points (b) and (c); and (2) be made in a form and manner established by the competent authority.
ATM/ANS.OR.A.070 Contingency plans
A service provider shall have in place contingency plans for all the services it provides in the case of events which result in significant degradation or interruption of its operations.
ATM/ANS.OR.A.075 Open and transparent provision of services
(a) A service provider shall provide its services in an open and transparent manner. It shall publish the conditions of access to its services and changes thereto and establish a consultation process with the users of its services on a regular basis or as needed for specific changes in service provision, either individually or collectively.
(b) A service provider shall not discriminate on grounds of nationality or other characteristic of the user or the class of users of its services in a manner that is contrary to Union law.
ATM/ANS.OR.A.080 Provision of aeronautical data
(a) A service provider shall ensure that aeronautical data related to its services is provided in due time to the AIS provider.
(b) When aeronautical data related to its services is published, the service provider shall: (1) monitor the data; (2) notify the AIS provider of any changes necessary to ensure that the data is correct and complete; (3) notify the AIS provider when the data is incorrect or inappropriate.
ATM/ANS.OR.A.085 Aeronautical data quality management
When originating, processing or transmitting data to the AIS provider, the service provider shall:
(a) ensure that aeronautical data referred to in Appendix 1 conform to the specifications of the aeronautical data catalogue;
(b) ensure that the following data quality requirements are met: (1) the accuracy of aeronautical data is as specified in the aeronautical data catalogue; (2) the integrity of aeronautical data is maintained; (3) based on the integrity classification specified in the aeronautical data catalogue, procedures are put in place so that: (i) for routine data, corruption is avoided throughout the processing of the data; (ii) for essential data, corruption does not occur at any stage of the entire process and additional processes are included, as needed, to address potential risks in the overall system architecture to further assure data integrity at this level; (iii) for critical data, corruption does not occur at any stage of the entire process and additional integrity assurance processes are included to fully mitigate the effects of faults identified as potential data integrity risks by thorough analysis of the overall system architecture; (4) the resolution of aeronautical data is commensurate with the actual data accuracy; (5) the traceability of aeronautical data is ensured; (6) the timeliness of the aeronautical data is ensured, including any limits on the effective period of the data; (7) the completeness of the aeronautical data is ensured; (8) the delivered data meet the specified format requirements;
(c) with regard to data origination, establish specific formal arrangements with the party originating data that contain instructions for data creation, modification or deletion, which include as a minimum: (1) an unambiguous description of the aeronautical data to be created, modified or deleted; (2) the entity to which the aeronautical data is to be provided; (3) the date and time by which the aeronautical data is to be provided; (4) the format of the data origination report to be used; (5) the format of the aeronautical data to be transmitted; (6) the requirement to identify any limitation on the use of the data;
(d) ensure that data validation and verification techniques are employed to ensure that the aeronautical data meets the associated data quality requirements and in addition: (1) the verification shall ensure that aeronautical data is received without corruption and that corruption does not occur at any stage of the entire aeronautical data process; (2) aeronautical data and aeronautical information entered manually shall be subject to independent verification to detect any errors that may have been introduced; (3) when using aeronautical data to derive or calculate new aeronautical data, the initial data shall be verified and validated, except when provided by an authoritative source;
(e) transmit aeronautical data by electronic means;
(f) establish formal arrangements with: (1) all parties transmitting data to them; (2) other service providers or aerodrome operators when exchanging aeronautical data and aeronautical information;
(g) ensure that the information listed in point AIS.TR.505(a) is provided in due time to the AIS provider;
(h) collect and transmit metadata which include as a minimum: (1) the identification of the organisations or entities performing any action of originating, transmitting or manipulating the aeronautical data; (2) the action performed; (3) the date and time the action was performed;
(i) ensure that tools and software used to support or automate aeronautical data and aeronautical information processes perform their functions without adversely impacting the quality of aeronautical data and aeronautical information;
(j) ensure that digital data error detection techniques are used during the transmission or storage of aeronautical data, or both, in order to support the applicable data integrity levels;
(k) ensure that the transfer of aeronautical data is subject to a suitable authentication process such that recipients are able to confirm that the data has been transmitted by an authorised source;
(l) ensure that errors identified during data origination and after data delivery are addressed, corrected or resolved and that priority is given to managing errors in critical and essential aeronautical data.
ATM/ANS.OR.A.090 Common reference systems for air navigation
For the purpose of air navigation, service providers shall use:
(a) the World Geodetic System – 1984 (WGS-84) as the horizontal reference system;
(b) the mean sea level (MSL) datum as the vertical reference system;
(c) the Gregorian calendar and coordinated universal time (UTC) as the temporal reference systems.
SUBPART B — MANAGEMENT (ATM/ANS.OR.B)
ATM/ANS.OR.B.001 Technical and operational competence and capability
A service provider shall ensure that it is able to provide its services in a safe, efficient, continuous and sustainable manner, consistent with any foreseen level of overall demand for a given airspace. To this end, it shall maintain adequate technical and operational capacity and expertise.
ATM/ANS.OR.B.005 Management system
(a) A service provider shall implement and maintain a management system that includes: (1) clearly defined lines of responsibility and accountability throughout its organisation, including a direct accountability of the accountable manager; (2) a description of the overall philosophies and principles of the service provider with regard to safety, quality, and security of its services, collectively constituting a policy, signed by the accountable manager; (3) the means to verify the performance of the service provider's organisation in light of the performance indicators and performance targets of the management system; (4) a process to identify changes within the service provider's organisation and the context in which it operates, which may affect established processes, procedures and services and, where necessary, change the management system and/or the functional system to accommodate those changes; (5) a process to review the management system, identify the causes of substandard performance of the management system, determine the implications of such substandard performance, and eliminate or mitigate such causes; (6) a process to ensure that the personnel of the service provider are trained and competent to perform their duties in a safe, efficient, continuous and sustainable manner. In this context, the service provider shall establish policies for the recruitments and training of its personnel; (7) a formal means for communication that ensures that all personnel of the service provider are fully aware of the management system that allows critical information to be conveyed and that makes it possible to explain why particular actions are taken and why procedures are introduced or changed; (8) a process to ensure that the design of ATM/ANS equipment, or the changes to its design, subject to Article 6 of Delegated Regulation (EU) 2023/1768 comply with the applicable specifications, including independent checking function of the demonstration of compliance on the basis of which the ATM/ANS provider issues a statement of compliance and the associated compliance documentation thereto.
(b) A service provider shall document all management system key processes, including a process for making personnel aware of their responsibilities, and the procedure for the amendment of those processes.
(c) A service provider shall establish a function to monitor compliance of its organisation with the applicable requirements and the adequacy of the procedures. Compliance monitoring shall include a feedback system of findings to the accountable manager to ensure effective implementation of corrective actions as necessary.
(d) A service provider shall monitor the behaviour of its functional system and, where underperformance is identified, it shall establish its causes and eliminate them or, after having determined the implication of the underperformance, mitigate its effects.
(e) The management system shall be proportionate to the size of the service provider and the complexity of its activities, taking into account the hazards and associated risks inherent in those activities.
(f) Within its management system, the service provider shall establish formal interfaces with the relevant service providers and aviation undertakings in order to: (1) ensure that the aviation safety hazards entailed by its activities are identified and evaluated, and the associated risks are managed and mitigated as appropriate; (2) ensure that it provides its services in accordance with the requirements of this Regulation.
(g) In the case that the service provider holds also an aerodrome operator certificate, it shall ensure that the management system covers all activities in the scope of its certificates.
ATM/ANS.OR.B.005A Information security management system
In addition to the management system referred to in point ATM/ANS.OR.B.005, the service provider shall establish, implement and maintain an information security management system in accordance with Implementing Regulation (EU) 2023/203 in order to ensure the proper management of information security risks which may have an impact on aviation safety.
ATM/ANS.OR.B.010 Change management procedures
(a) A service provider shall use procedures to manage, assess and, if necessary, mitigate the impact of changes to its functional systems in accordance with points ATM/ANS.OR.A.045, ATM/ANS.OR.C.005, ATS.OR.205 and ATS.OR.210, as applicable.
(b) The procedures referred to in point (a) or any material modifications to those procedures shall: (1) be submitted, for approval, by the service provider to the competent authority; (2) not be used until approved by the competent authority.
(c) When the approved procedures referred to in point (b) are not suitable for a particular change, the service provider shall: (1) make a request to the competent authority for an exemption to deviate from the approved procedures; (2) provide the details of the deviation and the justification for its use to the competent authority; (3) not use the deviation before being approved by the competent authority.
ATM/ANS.OR.B.015 Contracted activities
(a) Service providers may contract activities to external organisations, as necessary, in support of their operations.
(b) Without prejudice to Article 7(4) of Regulation (EU) 2024/2803, a service provider shall ensure that the activities comprised in ATM/ANS falling under the definition set out in Article 3, point (5), of Regulation (EU) 2018/1139 for which specific requirements as set out in Annexes III to XIII are applicable under this Regulation shall only be contracted to an organisation that holds a certificate including the relevant term(s) of approval, or has submitted a declaration, as applicable.
(c) Ancillary activities may be contracted to an organisation that does not hold a certificate, nor has submitted a declaration.
(d) Ancillary activities shall only be contracted where it has been ascertained that any impact on the provision of the services can be effectively managed.
(e) The service provider shall regularly monitor the performance of its contracted activities.
ATM/ANS.OR.B.016 Use of resources from non-certified organisations
Where a service provider makes use of personnel or equipment provided by an external organisation, it shall ensure that:
(a) such personnel and equipment are fully integrated into its functional and management system, and that operational control is maintained;
(b) the responsibility for the activity remains fully with the service provider;
(c) a formal contract is concluded to this effect.
ATM/ANS.OR.B.020 Personnel requirements
(a) A service provider shall appoint an accountable manager, who has the authority over ensuring that all activities can be financed and carried out in accordance with the applicable requirements. The accountable manager shall be responsible for establishing and maintaining an effective management system.
(b) A service provider shall define the authority, duties and responsibilities of the nominated post holders, in particular of the management personnel in charge of safety, quality, security, finance and human resources-related functions as applicable.
ATM/ANS.OR.B.025 Facilities requirements
A service provider shall ensure that there are adequate and appropriate facilities to perform and manage all tasks and activities in accordance with the applicable requirements.
ATM/ANS.OR.B.030 Record-keeping
(a) A service provider shall establish a system of record-keeping that allows adequate storage of the records and reliable traceability of all its activities, covering in particular all the elements indicated in point ATM/ANS.OR.B.005.
(b) The format and the retention period of the records referred to in point (a) shall be specified in the service provider's management system procedures.
(c) Records shall be stored in a manner that ensures protection against damage, alteration and theft.
ATM/ANS.OR.B.035 Operations manuals
(a) A service provider shall provide and keep up to date its operations manuals relating to the provision of its services for the use and guidance of operations personnel.
(b) It shall ensure that: (1) operations manuals contain the instructions and information required by the operations personnel to perform their duties; (2) relevant parts of the operations manuals are accessible to the personnel concerned; (3) the operations personnel are informed of amendments to the operations manual applying to their duties in a manner that enables their application as of their entry into force.
SUBPART C — SPECIFIC ORGANISATION REQUIREMENTS FOR SERVICE PROVIDERS OTHER THAN ATS PROVIDERS (ATM/ANS.OR.C)
ATM/ANS.OR.C.001 Scope
This Subpart establishes the requirements to be met by the service provider other than the air traffic services provider, in addition to the requirements set out in Subparts A and B.
ATM/ANS.OR.C.005 Safety support assessment and assurance of changes to the functional system
(a) For any change notified in accordance with point ATM/ANS.OR.A.045(a)(1), the service provider other than the air traffic services provider shall: (1) ensure that a safety support assessment is carried out covering the scope of the change which is: (i) the equipment, procedural and human elements being changed; (ii) interfaces and interactions between the elements being changed and the remainder of the functional system; (iii) interfaces and interactions between the elements being changed and the context in which it is intended to operate; (iv) the life cycle of the change from definition to operations including transition into service; (v) planned degraded modes; (2) provide assurance, with sufficient confidence, via a complete, documented and valid argument that the service will behave and will continue to behave only as specified in the specified context.
(b) A service provider other than an air traffic services provider shall ensure that the safety support assessment referred to in point (a) comprises: (1) verification that: (i) the assessment corresponds to the scope of the change as defined in point (a)(1); (ii) the service behaves only as specified in the specified context; (iii) the way the service behaves complies with and does not contradict any applicable requirements of this Regulation placed on the services provided by the changed functional system; and (2) specification of the monitoring criteria necessary to demonstrate that the service delivered by the changed functional system will continue to behave only as specified in the specified context.
SUBPART D — SPECIFIC ORGANISATIONAL REQUIREMENTS FOR ANS AND ATFM PROVIDERS AND THE NETWORK MANAGER (ATM/ANS.OR.D)
ATM/ANS.OR.D.001 Scope
This Subpart establishes the requirements to be met by air navigation services (ANS) and air traffic flow management (ATFM) providers and the Network Manager, in addition to the requirements set out in Subparts A, B and C.
ATM/ANS.OR.D.005 Business, annual, and performance plans
(a) Business plan
(1) Air navigation services and air traffic flow management providers shall produce a business plan covering a minimum period of five years. The business plan shall: (i) set out the overall aims and goals of the air navigation services and of the air traffic flow management providers, and their strategy towards achieving them in consistency with any overall longer-term plan of the air navigation services provider or of the air traffic flow management provider and with the relevant requirements of Union law for the development of infrastructure or other technology; (ii) contain performance targets in terms of safety, capacity, environment and cost-efficiency, as may be applicable pursuant to Commission Implementing Regulation (EU) No 390/2013 ( 8 ).
(2) The information listed in points (i) and (ii) of point (1) shall be aligned with the performance plan referred to in Article 11 of Regulation (EC) No 549/2004 and, as far as safety data is concerned, it shall be consistent with the state safety programme referred to in Standard 3.1.1 of Annex 19 to the Chicago Convention in its first edition of July 2013.
(3) Air navigation services and air traffic flow management providers shall provide safety and business justifications for major investment projects including, where relevant, the estimated impact on the appropriate performance targets referred to in point (1)(ii) and identifying investments stemming from the legal requirements associated with the implementation of the Single European Sky ATM Research Programme (SESAR).
(b) Annual plan
(1) Air navigation services and air traffic flow management providers shall produce an annual plan covering the forthcoming year which shall further specify the features of the business plan and describe any changes to it as compared to the previous plan.
(2) The annual plan shall cover the following provisions on the level and quality of service, such as the expected level of capacity, safety, environment and cost-efficiency: (i) information on the implementation of new infrastructure or other developments, and a statement on how they will contribute to improving the performance of the air navigation services provider or of the air traffic flow management provider, including level and quality of services; (ii) performance indicators, as may be applicable, consistent with the performance plan referred to in Article 11 of Regulation (EC) No 549/2004, against which the performance level and quality of service may be reasonably assessed; (iii) information on the measures foreseen to mitigate the safety risks identified by the air navigation services and air traffic flow management provider, including safety indicators to monitor safety risk and, where appropriate, the estimated cost of mitigation measures; (iv) the air navigation services and air traffic flow management providers' expected short-term financial position as well as any changes to or impacts on the business plan.
(c) Performance part of the plans
The air navigation services and the air traffic flow management providers shall make the content of the performance part of their business plans and of their annual plans available to the Commission on its request, under the conditions set by the competent authority in accordance with national law.
ATM/ANS.OR.D.010 Security management
(a) Air navigation services and air traffic flow management providers and the Network Manager shall, as an integral part of their management system as required in point ATM/ANS.OR.B.005, establish a security management system to ensure: (1) the security of their facilities and personnel so as to prevent unlawful interference with the provision of services; (2) the security of operational data they receive, or produce, or otherwise employ, so that access to it is restricted only to those authorised.
(b) The security management system shall define: (1) the process and procedures relating to security risk assessment and mitigation, security monitoring and improvement, security reviews and lesson dissemination; (2) the means designed to identify, monitor and detect security breaches and to alert personnel with appropriate security warnings; (3) the means to control the effects of security breaches and to identify recovery action and mitigation procedures to prevent re-occurrence.
(c) Air navigation services and air traffic flow management providers and the Network Manager shall ensure the security clearance of their personnel, if appropriate, and coordinate with the relevant civil and military authorities to ensure the security of their facilities, personnel and data.
(d) The aspects related to information security shall be managed in accordance with point ATM/ANS.OR.B.005A.
ATM/ANS.OR.D.015 Financial strength — economic and financial capacity
Air navigation services and air traffic flow management providers shall be able to meet their financial obligations, such as fixed and variable costs of operation or capital investment costs. They shall use an appropriate cost-accounting system. They shall demonstrate their ability through the annual plan as referred to in point ATM/ANS.OR.D.005(b), as well as through balance sheets and accounts, as applicable under their legal statute, and regularly undergo an independent financial audit.
ATM/ANS.OR.D.020 Liability and insurance cover
(a) Air navigation services and air traffic flow management providers and the Network Manager shall have in place arrangements to cover liabilities related to the execution of their tasks in accordance with the applicable law.
(b) The method employed to provide the cover shall be appropriate to the potential loss and damage in question, taking into account the legal status of the providers concerned and the Network Manager and the level of commercial insurance cover available.
(c) Air navigation services and air traffic flow management providers and the Network Manager which avail themselves of services of another service provider shall ensure that the agreements that they conclude to that effect specify the allocation of liability between them.
ATM/ANS.OR.D.025 Reporting requirements
(a) Air navigation services and air traffic flow management providers shall provide an annual report of their activities to the competent authority.
(b) For air navigation services and air traffic flow management providers, the annual report shall cover their financial results, without prejudice to Article 12 of Regulation (EC) No 550/2004, as well as their operational performance and any other significant activities and developments in particular in the area of safety.
(c) The Network Manager shall provide an annual report of its activities to the Commission and the Agency. This report shall cover its operational performance, as well as significant activities and developments in particular in the area of safety.
(d) The annual reports referred to in points (a) and (c) shall include as a minimum: (1) an assessment of the level of performance of services provided; (2) for air navigation services and air traffic flow management providers, their performance compared to the performance targets established in the business plan referred to in point ATM/ANS.OR.D.005(a), comparing actual performance against the performance set out in the annual plan by using the indicators of performance established in the annual plan; (3) for the Network Manager, its performance compared to the performance objectives established in the Network Strategy Plan, comparing actual performance against the performance set out in the Network Operational Plan by using the indicators of performance established in the Network Operational Plan; (4) an explanation for differences with the relevant targets and objectives and an identification of the measures required to address any gaps between the plans and actual performance, during the reference period referred to in Article 11 of Regulation (EC) No 549/2004; (5) developments in operations and infrastructure; (6) the financial results, where they are not published separately in accordance with Article 12(1) of Regulation (EC) No 550/2004; (7) information about the formal consultation process with the users of its services; (8) information about the human resources policy.
(e) Air navigation services and air traffic flow management providers and the Network Manager shall make their annual reports available to the Commission and the Agency on their request. They shall also make those reports available to the public, under the conditions set by the competent authority in accordance with Union and national law.
Appendix 1 AERONAUTICAL DATA CATALOGUE Introduction (a) The aeronautical data catalogue is a reference to the aeronautical data subjects, properties and sub-properties organised in: (1) aerodrome data; (2) airspace data; (3) ATS and other routes data; (4) instrument flight procedure data; (5) radio navigation aids/systems data; (6) obstacle data; (7) geographical position data. (b) The tables of the aeronautical data catalogue are composed of the following columns: (1) subject for which data can be collected; (2) property: an identifiable characteristic of a subject which may be further defined into sub-properties; (3) same as 2; (4) types: the data is classified into different types; (5) description: a description of the data item; (6) notes: containing additional information or conditions for the provision of the data; (7) accuracy: requirements for aeronautical data are based on a 95 % confidence level; (8) integrity classification; (9) origination type: data is identified as surveyed, calculated or declared; (10) publication resolution; (11) chart resolution. Note for items 2 and 3 under point (b): the classification of a catalogue element as subject, property or sub-property does not impose a certain data model. Note for item 7 under point (b): for those fixes and points that serve a dual purpose, e.g. holding point and missed approach point, the higher accuracy applies. Accuracy requirements for obstacle and terrain data are based on a 90 % confidence level. Note for item 10 under point (b): the publication resolutions for geographical position data (latitude and longitude) are applicable to coordinates formatted in degrees, minutes, seconds. When a different format is used (such as degrees with decimals for digital data sets) or when the location is significantly further to the north/south, the publication resolution needs to be commensurate with the accuracy requirements. 1. Aerodrome data Subject Property Sub-property Type Description Note Accuracy Integrity Orig. Type Pub. Res. Chart Res. Aerodrome/Heliport A defined area on land or water (including any buildings, installations and equipment) intended to be used either wholly or in part for the arrival, departure and surface movement of aircraft. Designator Designator of the aerodrome/heliport ICAO location indicator Text The four-letter ICAO location indicator of the aerodrome/heliport, as listed in ICAO Doc 7910 ‘Location Indicators’ If any IATA designator Text The identifier that is assigned to a location in accordance with IATA rules (Resolution 767) If any Other Text A locally defined airport identifier, if other than an ICAO location indicator Name Text The primary official name of an aerodrome as designated by the competent authority Served city Text The full name (free text) of the city or town the aerodrome/ heliport is serving Type of traffic permitted International/national Code list Indication if international and/or national flights are permitted at the aerodrome/ heliport Instrument flight rules (IFR)/ Visual flight rules (VFR) Code list Indication if IFR and/or VFR flights are permitted at the aerodrome/heliport Scheduled/ non-scheduled Code list Indication if scheduled and/or non-scheduled flights are permitted at the aerodrome/heliport Civil/military Code list Indication if civil commercial aviation and/or general aviation and/or military flights are permitted at the aerodrome/ heliport Restricted use Text Indication if an aerodrome or heliport is not open for the public (only for use by the owners) Heliport type Text The type of the heliport (surface level, elevated, shipboard or helideck) Control type Text Indication if an aerodrome is under civil control, military control or joint control Certified Text Indication if an aerodrome is/is not certified in accordance with the ICAO rules or Regulation (EU) No 139/2014 Certification date Date The date when the airport certification was issued by the competent authority Certification expiration date Date The date when the aerodrome certification becomes invalid Field elevation Elevation Elevation The vertical distance above mean sea level (MSL) from the highest point of the landing area 0,5 m Essential Surveyed 1 m or 1 ft 1 m or 1ft Geoid undulation Height The geoid undulation at the aerodrome/ heliport elevation position Where appropriate 0,5 m Essential Surveyed 1 m or 1 ft 1 m or 1ft Reference temperature Value The monthly mean of the daily maximum temperatures for the hottest month of the year at an aerodrome; this temperature must be averaged over a period of years. Mean low temperature Value The mean lowest temperature of the coldest month of the year, for the last five years of data at the aerodrome elevation 5 degrees Magnetic variation The angular difference between the true and the magnetic north Angle Angle The angle value of the magnetic variation 1 degree Essential Surveyed 1 degree 1 degree Date Date The date on which the magnetic variation had the corresponding value Annual change Value The annual rate of change of the magnetic variation Reference point The designated geographical location of an aerodrome Position Point Geographical location of the aerodrome reference point 30 m Routine Surveyed/calculated 1 sec 1 sec Site Text Location of the reference point on the aerodrome Direction Text Direction of the aerodrome reference point from the centre of the city or town which the aerodrome serves Distance Distance Distance of the aerodrome reference point from the centre of the city or town which the aerodrome serves Landing direction indicator A device to visually indicate the direction currently designated for landing and for take-off Location Text Location of the landing direction indicator Lighting Text Lighting of the landing direction indicator If any Secondary power supply Characteristics Text Description of the secondary power supply Switch-over time Value Secondary power supply switch-over time Anemometer Device used for measuring the wind speed Location Text Location of the anemometer Lighting Text Lighting of the anemometer If any Aerodrome beacon (ABN)/ identification beacon (IBN) Aerodrome beacon/identification beacon used to indicate the location of an aerodrome from the air Location Text Location of the aerodrome beacon/identification beacon If any Characteristics Text Description of the aerodrome beacon/identification beacon Hours of operation Schedule Hours of operation of the aerodrome beacon/identification beacon Wind direction indicator Location Text Location of the wind direction indicator Lighting Text Lighting of the wind direction indicator Runway visual range (RVR) observation site The observation site of the RVR Position Point Geographical location of the RVR observation sites Frequency area The designated part of a surface movement area where a specific frequency is required by ATC or ground control Station Text Name of the station providing the service Frequency Value Frequency of the station providing the service Boundary Polygon Area boundary of the frequency area Hot spot A location on an aerodrome movement area with a history, or potential risk, of collision or RWY incursion, and where heightened attention by pilots/drivers is necessary Identifier Text The identifier of the hot spot Annotation Text Additional information about the hot spot Geometry Polygon Geographical area of the hot spot Subject Property Sub-property Type Description Note Accuracy Integrity Orig. Type Pub. Res. Chart Res. RWY A defined rectangular area on a land aerodrome prepared for the landing and take-off of aircraft Designator Text The full textual designator of the RWY, used to uniquely identify the RWY at an aerodrome/heliport (e.g. 09/27, 02R/20L, RWY 1) Nominal length Distance The declared longitudinal extent of the RWY for operational (performance) calculations 1 m Critical Surveyed 1 m or 1 ft 1 m Nominal width Distance The declared transversal extent of the RWY for operational (performance) calculations 1 m Essential Surveyed 1 m or 1 ft 1 m Geometry Polygon Geometries of the RWY element, RWY displaced area and RWY intersection Centre line points Position Point Geographical location of the RWY centre line at each end of the RWY, at the stopway (SWY), and at the origin of each take-off flight path area, as well as at each significant change in the slope of the RWY and SWY Definition from Annex 4 3.8.4.2 1 m Critical Surveyed Elevation Elevation The elevation of the corresponding centre line point. For non-precision approaches, any significant high and low intermediate points along the RWY shall be measured to the accuracy of one-half metre or foot. 0,25 m Critical Surveyed Geoid undulation Height The geoid undulation at the corresponding centre line point RWY exit line Exit guidance line Line Geographical location of the RWY exit line 0,5 m Essential Surveyed 1/100 sec 1 sec Colour Text Colour of the RWY exit line Style Text Style of the RWY exit line Directionality Code list Directionality of the RWY exit line (one-way or two-way) Surface type Text The surface type of the RWY Strength Pavement classification number (PCN) Text PCN Pavement type Text Pavement type for the aircraft classification number — pavement classification number (ACN-PCN) determination Subgrade category Text Subgrade strength category of the RWY Allowable pressure Text The maximum allowable tyre pressure category or the maximum allowable tyre pressure value Evaluation method Text The evaluation method used Strip A defined area including the RWY and the SWY, if provided: to reduce the risk of damage to aircraft running off a RWY; and to protect aircraft flying over the RWY during take-off or landing operations Length Distance The longitudinal extent of the RWY strip Width Distance The transversal extent of the RWY strip Surface type Text The surface type of the RWY strip Shoulder An area adjacent to the edge of a pavement, so prepared as to provide a transition area between the pavement and the adjacent surface Geometry Polygon Geographical location of the RWY shoulders Surface type Text The surface type of the RWY shoulder Width Distance The width of the RWY shoulder 1 m Essential Surveyed 1 m or 1 ft Blast pad Specially prepared surface placed adjacent to the end of a RWY to eliminate the erosive effect of the strong wind forces produced by aeroplanes at the beginning of their take-off roll Geometry Polygon Geographical location of the blast pad Obstacle-free zone Text Existence of an obstacle-free zone for a precision approach RWY category I When provided RWY marking Type Text Type of the RWY marking Description Text Description of the RWY marking Geometry Polygon The geographical location of the RWY marking RWY centre line LGT Length Distance The longitudinal extent of the RWY centre line lights Spacing Distance Spacing of the RWY centre line lights Colour Text Colour of the RWY centre line lights Intensity Text Intensity of the RWY centre line lights Position Point Geographical location of each individual light of the RWY centre line lights RWY edge LGT Length Distance The longitudinal extent of the RWY edge lights Spacing Distance Spacing of the RWY edge lights Colour Text Colour of the RWY edge lights Intensity Text Intensity of the RWY edge lights Position Point Geographical location of each individual light of the RWY edge lights Reference code The intent of the reference code is to provide a simple method for interrelating the numerous specifications concerning the characteristics of aerodromes so as to provide a series of aerodrome facilities that are suitable for the aeroplanes intended to operate at the aerodrome. Number Code list A number based on the aeroplane reference field length Letter Code list A letter based on the aeroplane wingspan and outer main gear wheel span Restriction Text Description of restrictions imposed on the RWY RWY direction Designator Text The full textual designator of the landing and take-off direction — examples: 27, 35L, 01R True bearing Bearing The true bearing of the RWY 1/100 degree Routine Surveyed 1/100 degree 1 degree Type Text Type of RWY: precision (Cat I, II, III)/ non-precision/ non-instrument Threshold The beginning of the portion of the RWY usable for landing Position Point The geographical location of the RWY threshold 1 m Critical Surveyed 1/100 sec 1 sec Elevation Elevation Elevation of the RWY threshold See Note 1 Geoid undulation Height WGS-84 geoid undulation at the RWY threshold position See Note 2 Type Text The indication if the threshold is displaced or not displaced; a displaced threshold is not located at the extremity of the RWY Displacement Distance Distance of the displaced threshold If threshold displaced 1 m Routine Surveyed RWY end RWY end (flight path alignment point) Position Point Location of the RWY end in the direction of departure 1 m Critical Surveyed 1/100 sec 1 sec Elevation Elevation Elevation of the end position of the RWY See RWY centre line points Departure end of RWY (DER) The end of the area declared suitable for take-off (i.e. the end of the RWY or, where a clearway is provided, the end of the clearway) Beginning of the departure procedure Position Point The geographical location of the DER Elevation Elevation The elevation of the DER is the elevation of the end of the RWY or of the clearway, whichever is higher. Touchdown zone The portion of a RWY beyond the threshold, where landing aeroplanes are intended to first contact the RWY Elevation Elevation The highest elevation of the touchdown zone of a precision approach RWY Precision approach RWY 0,25 m or 0,25 ft Slope Value The slope of the RWY touchdown zone Slope Value The slope of the RWY Land-and-hold short operations (LAHSOs) LAHSOs Geometry Line The geographical location of the LAHSOs Protected element Text The name of the RWY or taxiway (TWY) being protected Displaced area The portion of a RWY between the beginning of the RWY and the displaced threshold Geometry Polygon Geographical location of the displaced area PCN Text The PCN of the displaced area Surface type Text The surface type of the displaced area Aircraft restriction Text Usage restriction for a specific aircraft type SWY A defined rectangular area on the ground at the end of the take-off RWY available, prepared as a suitable area in which an aircraft may be stopped in case of an abandoned take-off Length Distance The longitudinal extent of the SWY If any 1 m Critical Surveyed 1 m or 1 ft 1 m Width Distance The width of the SWY 1 m Critical Surveyed 1 m or 1 ft 1 m Geometry Polygon Geographical location of the SWY Slope Value The slope of the SWY Surface type Text The surface type of the SWY Clearway A defined rectangular area on the ground or water under the control of the appropriate authority, selected or prepared as a suitable area over which an aeroplane may make a portion of its initial climb to a specified height Length Distance The longitudinal extent of the clearway 1 m Essential Surveyed 1 m or 1 ft Width Distance The transversal extent of the clearway 1 m Essential Surveyed 1 m or 1 ft Ground profile The vertical profile (or slope) of the clearway If any RWY end safety area (RESA) An area symmetrical about the extended RWY centre line and adjacent to the end of the strip, primarily intended to reduce the risk of damage to an aeroplane undershooting or overrunning the RWY Length Distance The longitudinal extent of the RESA Width Distance The transversal extent of the RESA Longitudinal slope Value The longitudinal slope of the RESA Transversal slope Value The transversal slope of the RESA Declared distances Take-off run available (TORA) Distance The length of the RWY, declared available and suitable for the ground run of an aeroplane taking off 1 m Critical Surveyed 1 m or 1 ft 1 m Take-off distance available (TODA) Distance The length of the take-off run available plus the length of the clearway, if provided 1 m Critical Surveyed 1 m or 1 ft 1 m Accelerate-stop distance available (ASDA) Distance The length of the take-off run available plus the length of the SWY, if provided 1 m Critical Surveyed 1 m or 1 ft 1 m Landing distance available (LDA) Distance The length of the RWY, declared available and suitable for the ground run of an aeroplane landing 1 m Critical Surveyed 1 m or 1 ft 1 m Remarks Text Remarks including RWY entry or start point, where alternative reduced distances have been declared RWY end LGT Colour Text Colour of the RWY end lights Position Point Geographical location of each individual light of the RWY end lights SWY LGT Length Distance The longitudinal extent of the SWY lights Colour Text Colour of the SWY lights Position Point Geographical location of each individual light of the SWY lights Approach lighting system Type Text Classification of the approach lighting system, using as criteria Regulation (EU) No 139/2014 and CS-ADR-DSN, especially CS ADR-DSN.M.625 and CS ADR-DSN.M.626 Length Distance The longitudinal extent of the approach lighting system Intensity Text A code indicating the relative intensity of the approach lighting system Position Point Geographical location of each individual light of the approach lighting system RWY threshold lights Colour Text Colour of the RWY threshold lights Wing bar colour Text Colour of the RWY threshold wing bars Position Point Geographical location of each individual light of the threshold and wing bar lights Touchdown zone lights Length Distance The longitudinal extent of the RWY touchdown zone lights Position Point Geographical location of each individual light of the RWY touchdown zone lights Visual-approach slope indicator system Minimum eye height over the threshold (MEHT) Height MEHT Location Point Geographical location of the visual-approach slope indicator system Angle Angle The nominal-approach slope angle(s) Type Text The type of visual approach indicator system (PAPI, A-PAPI. etc.) Displacement angle Angle Where the axis of the system is not parallel to the RWY centre line, the angle of and the direction of displacement, i.e. left or right Displacement direction Text Where the axis of the system is not parallel to the RWY centre line, the angle of and the direction of displacement, i.e. left or right Arresting gear Line The geographical location of the arresting-gear cable across the RWY Arresting system High-energy-absorbing material located at the end of a RWY or SWY, designed to be crushed under the weight of an aeroplane as the material exerts deceleration forces on the aircraft landing gear Geometry Polygon Geographical location of the arresting system Setback Distance Setback of the arresting system Length Distance The longitudinal extent of the arresting system Width Distance The transversal extent of the arresting system Radio altimeter area Length Distance The longitudinal extent of the radio altimeter area Width Distance The transversal extent of the radio altimeter area Geometry Polygon Geographical location of the radio altimeter area Note 1 Threshold elevation for RWYs with non-precision approaches 0,5 m Essential Surveyed 1 m or 1ft 1 m or 1 ft Threshold elevation for RWYs with precision approaches 0,25 m Critical Surveyed 0,1 m or 0,1 ft 0,5 m or 1 ft Note 2 WGS-84 geoid undulation at the RWY threshold for non-precision approaches 0,5 m Essential Surveyed 1 m or 1ft 1 m or 1 ft WGS-84 geoid undulation at the RWY threshold for precision approaches 0,25 m Critical Surveyed 0,1 m or 0,1 ft 0,5 m or 1 ft Subject Property Sub-property Type Description Note Accuracy Integrity Orig. Type Pub. Res. Chart Res Final-approach and take-off area (FATO) A defined area over which the final phase of the approach manoeuvre before hover or landing is completed and from which the take-off manoeuvre is commenced; where the FATO is used by helicopters operated in performance class 1, the defined area includes the rejected take-off area available. Threshold point The beginning of the portion of the FATO, usable for landing Position Point Geographical location of the FATO threshold point 1 m Critical Surveyed 1/100 sec 1 sec Elevation Elevation Elevation of the FATO threshold See Note 1 Geoid undulation Height WGS-84 geoid undulation at the FATO threshold position See Note 2 DER The end of the area declared suitable for take-off (i.e. the end of the RWY or, where a clearway is provided, the end of the clearway or the end of the FATO area) Position Point Geographical location of the DER 1 m Critical Surveyed 1/100 sec 1 sec Elevation Elevation The higher of the elevations of the beginning and of the end of the RWY/FATO Type Text Type of FATO Designation Text The full textual designator of the landing and take-off area Length Distance The longitudinal extent of FATO 1 m Critical Surveyed 1 m or 1 ft 1 m Width Distance The transversal extent of FATO Geometry Polygon Geographical location of the FATO element Slope Value The slope of FATO Surface type Text The surface type of FATO True bearing Bearing The true bearing of FATO 1/100 degree Routine Surveyed 1/100 degree Declared distances Take-off distance available (TODAH) Distance The FATO length plus the helicopter clearway length (if provided) And, if applicable, alternative reduced declared distances 1 m Critical Surveyed 1 m or 1 ft Rejected take-off distance available (RTODAH) Distance The length of FATO, declared available and suitable for helicopters operated in performance class 1, to complete a rejected take-off 1 m Critical Surveyed 1 m or 1 ft Landing distance available (LDAH) Distance The length of FATO plus any additional area declared available and suitable for helicopters to complete the landing manoeuvre from a defined height 1 m Critical Surveyed 1 m or 1 ft Remarks Text Remarks including RWY entry or start point, where alternative reduced distances have been declared FATO marking Description Text Description of the FATO markings Approach lighting system Type Text Classification of the approach lighting system, using as criteria Regulation (EU) No 139/2014 and CS-ADR-DSN, specifically CS ADR-DSN.M.625 and CS ADR-DSN.M.626 Length Distance The longitudinal extent of the approach lighting system Intensity Text A code indicating the relative intensity of the approach lighting system Position Point Geographical location of each individual light of the approach lighting system Area lights Description Text Description of the area lights Position Point Geographical location of each individual light of the area lights Aiming point lights Description Text Description of the aiming point lights Position Point Geographical location of each individual light of the aiming point lights Touchdown and lift-off area (TLOF) An area on which a helicopter may touch down or lift off Designator Text The full textual designator of TLOF Centre point Position Point Geographical location of the TLOF threshold point 1 m Critical Surveyed 1/100 sec 1 sec Elevation Elevation Elevation of the TLOF threshold See Note 1 Geoid undulation Height The WGS-84 geoid undulation TLOF centre point position See Note 2 Length Distance The longitudinal extent of TLOF 1 m Critical Surveyed 1 m or 1 ft 1 m Width Distance The transversal extent of TLOF 1 m Critical Surveyed 1 m or 1 ft 1 m Geometry Polygon The geographical location of the TLOF element Slope Value The slope of TLOF Surface type Text The surface type of TLOF Bearing strength Value The bearing strength of TLOF 1 ton Visual-approach slope indicator system type Text Type of the visual-approach slope indicator system Marking Description Text Description of the TLOF markings Safety area A defined area on a heliport surrounding the FATO, which is free of obstacles, other than those required for air navigation purposes, and intended to reduce the risk of damage to helicopters accidentally diverging from the FATO Length Distance The longitudinal extent of the safety area Width Distance The transversal extent of the safety area Surface type Text The surface type of the safety area Helicopter clearway A defined area on the ground or water, selected and/or prepared as a suitable area over which a helicopter operated in performance class 1 may accelerate and achieve a specific height Length Distance The longitudinal extent of the helicopter clearway Ground profile Value The vertical profile (or slope) of the helicopter clearway Note 1 The FATO threshold for heliports with or without a Point-in-Space (PinS) approach 0,5 m Essential Surveyed 1 m or 1 ft The FATO threshold for heliports intended to be operated 0,25 m Critical Surveyed 1 m or 1 ft (non-precision) 0,1 m or 0,1 ft (precision) Note 2 The WGS–84 geoid undulation at the FATO threshold and the TLOF geometric centre, for heliports with or without a PinS approach 0,5 m Essential Surveyed 1 m or 1 ft The WGS–84 geoid undulation at the FATO threshold and the TLOF geometric centre, for heliports intended to be operated 0,25 m Critical Surveyed 1 m or 1 ft (non-precision) 0,1 m or 0,1 ft (precision) Subject Property Sub-property Type Description Note Accuracy Integrity Orig. Type Pub. Res. Chart Res. Apron A defined area on a land aerodrome, intended to accommodate aircraft as regards loading or unloading passengers, mail or cargo, fuelling, parking or maintenance Designator Text The full textual name or designator used to identify an apron at an aerodrome/heliport Geometry Polygon Geographical location of the apron element 1 m Routine Surveyed 1/10 sec 1 sec Type Text Classification of the primary use of the apron Aircraft restriction Text Usage restriction (prohibition) for a specified aircraft type Surface type Text The surface type of the apron Strength PCN Text PCN of the apron Pavement type Text ACN-PCN determination Subgrade category Text Subgrade strength category of the apron Allowable pressure Text The maximum allowable tyre pressure category or the maximum allowable tyre pressure value Evaluation method Text The evaluation method used to determine the apron strength Elevation Elevation The elevation of the apron TWY A defined path on a land aerodrome, established for the taxiing of aircraft and intended to provide a link between one part of the aerodrome and another Designator Text The full textual designator of the TWY Width Distance The transversal extent of the TWY 1 m Essential Surveyed 1 m or 1 ft Geometry Polygon Geographical location of the TWY element Bridge Text Type of the bridge (none, overpass, underpass) Surface type Text Surface type of the TWY Strength PCN Text PCN of the TWY Pavement type Text ACN-PCN determination Subgrade category Text Subgrade strength category of the TWY Allowable pressure Text Maximum allowable tyre pressure category or maximum allowable tyre pressure value Evaluation method Text The evaluation method used to determine the taxiway strength Aircraft restrictions Text Usage restriction (prohibition) for a specified aircraft type Reference code letter Code list A letter based on the aeroplane wingspan and outer main gear wheel span Location for wing tips extension Point/Polygon For aerodromes accommodating aeroplanes with folding wing tips, the location where to extend the wing tips Centre line points Position Point Geographical coordinates of the TWY centre line points 0,5 m Essential Surveyed 1/100 sec 1/100 sec Elevation Elevation Elevation of taxiway centre line points 1 m Essential Surveyed Shoulder An area adjacent to the edge of a pavement, so prepared as to provide a transition between the pavement and the adjacent surface Geometry Polygon The geographical location of the TWY shoulder Surface type Text Surface type of the TWY shoulder Width Distance The width of the TWY shoulder 1 m Essential Surveyed 1 m or 1 ft Guidance lines Geometry Line Geographical location of the guidance lines 0,5 m Essential Surveyed 1/100 sec 1/100 sec Colour Text Colour of TWY guidance lines Style Text Style of TWY guidance lines Wingspan Value Wingspan Maximum speed Value Maximum speed Direction Text Direction Intermediate-holding-position marking line Line Intermediate holding position marking line 0,5 m Essential Surveyed 1/100 sec 1 sec TWY marking Description Text Description of the TWY marking TWY edge lights Description Text Description of the TWY edge lights Position Point Geographical location of each individual light of the TWY edge lights TWY centre line lights Description Text Description of the TWY centre line lights Position Point Geographical location of each individual light of the TWY centre line lights Stop bars Description Text Description of the stop bars If any Location Line Location of the stop bars RWY guard lights Description Text Description of the RWY guard lights and other RWY protection measures If any Location Point Location of the stop bar Configuration A Location Line Location of the stop bar Configuration B RWY holding position A designated position intended to protect a RWY, an obstacle limitation surface, or an instrument landing system (ILS)/microwave landing system (MLS) critical/sensitive area, at which taxiing aircraft and vehicles shall stop and hold, unless otherwise authorised by the aerodrome control tower Geometry Line Geographical location of the RWY holding position 0,5 m Essential Surveyed 1/100 sec 1 sec Protected RWY Text Designator of the RWY protected Cat stop Code list Category (CAT) of the RWY (0, I, II, III) RWY ahead text Text Actual text as in the marking; e.g. ‘RWY AHEAD’ or ‘RUNWAY AHEAD’ Intermediate holding position Geometry Line Geographical location of the intermediate holding position — a designated position intended for traffic control, at which taxiing aircraft and vehicles shall stop and hold until further cleared to proceed, when so instructed by the aerodrome control tower Helicopter ground TWY A ground TWY intended for the ground movement of wheeled undercarriage helicopters Designator Text The full textual designator of the helicopter ground TWY Centre line points Point Geographical location of the helicopter ground centre line TWY points 0,5 m Essential Surveyed/calculated Elevation Elevation Elevation of the helicopter ground TWY 1 m Essential Surveyed Width Distance The transversal extent of the helicopter ground TWY 1 m Essential Surveyed Surface type Text The surface type of the helicopter ground TWY Intersection marking line Line Helicopter ground TWY intersection marking line 0,5 m Essential Surveyed 1/100 sec 1 sec Lighting Description Text Description of the helicopter ground TWY light Position Point Geographical location of each individual light of the helicopter ground TWY lights Marking Description Text Description of helicopter ground TWY marking Helicopter air TWY A defined path on the surface, established for the air taxiing of helicopters Designator The full textual designator of the helicopter air TWY Centre line points Point Geographical location of the helicopter air TWY centre line points 0,5 m Essential Surveyed/calculated Elevation Elevation Elevation of the helicopter air TWY 1 m Essential Surveyed Width Distance The transversal extent of the helicopter air TWY 1 m Essential Surveyed Surface type Text Surface type of the helicopter air TWY Lighting Description Text Description of the helicopter air TWY lighting Position Point Geographical location of each individual light of the helicopter air TWY lights Marking Description Text Description of the helicopter air TWY marking Helicopter air transit routes A defined path established for the movement of helicopters from one part of a heliport to another; a taxiing route includes a helicopter air or ground TWY centred on the taxiing route. Designator Text Designator of the helicopter air transit route Geometry Line Geographical location of the helicopter air transit route Width Distance The transversal extent of the helicopter air transit route 1 m Essential Surveyed INS checkpoint Location Point Geographical location of the INS checkpoint Where available 0,5 m Routine Surveyed 1/100 sec 1/100 sec Very-high-frequency (VHF) omnidirectional range (VOR) checkpoint Location Point Geographical location of the VOR checkpoint Where available Frequency Value Frequency of the VOR checkpoint Altimeter checkpoint Location Point Geographical location of the altimeter checkpoints Elevation Elevation Elevation of the altimeter checkpoints Aircraft stand A designated area on an apron intended to be used for parking an aircraft Name Text Name of the aircraft stand point Aircraft stand points Location Point Geographical location of the aircraft stand point 0,5 m Routine Surveyed 1/100 sec 1/100 sec Aircraft types Code list Aircraft types Identification sign Text Description of the aircraft stand identification sign Visual docking/parking guidance system Text Description of the visual docking/parking guidance system at the aircraft stand Parking-stand area Polygon Geographical location of the parking-stand area Jetway Code list Jetway available at the aircraft stand Fuel Code list Fuel available at the aircraft stand Ground power Code list Ground power available at the aircraft stand Towing Code list Towing available at the aircraft stand Terminal Text Terminal-building reference Surface type Text Surface type of the aircraft stand Aircraft restriction Text Usage restriction (prohibition) for a specified aircraft type PCN Text PCN of the aircraft stand Stand guidance line Geometry Line Geographical location of the stand guidance line 0,5 m Essential Surveyed 1/100 sec Elevation Elevation Elevation of the parking guidance line points 1 m Essential Surveyed Direction Text Direction of the stand guidance line Wingspan Value Wingspan Colour Code list Colour of the stand guidance line Style Code list Style of the stand guidance line Helicopter stand An aircraft stand that provides for parking a helicopter, and where ground taxi operations are completed, or where the helicopter touches down and lifts off for air taxiing operations. Name Text Name of the helicopter stand Location Point Geographical location of the helicopter stand point/INS checkpoints 0,5 m Essential Surveyed 1/100 sec De-icing area A facility where frost, ice or snow is removed (de-icing) from the aeroplane to provide clean surfaces, and/or where clean surfaces of the aeroplane receive protection (anti-icing) against the formation of frost or ice, and accumulation of snow or slush, for a limited period of time Identifier Text Identifier of the de-icing area Geometry Polygon Geographical location of the de-icing area 1 m Routine Surveyed 1/10 sec 1 sec Surface type Text The surface type of the de-icing area Id base Text Name of the underlying TWY, parking stand or apron element Aircraft restriction Text Usage restriction (prohibition) for a specified aircraft type Subject Property Sub-property Type Description Note Accuracy Integrity Orig. Type Pub. Res. Chart Res. Communication facility Service designation Text Designation of the service provided Call sign Text Call sign of the communication facility Channel Text Channel/frequency of the communication facility Logon address Text Logon address of the facility As appropriate Hours of operation Schedule Operational hours of the station serving the unit 2. Airspace data Subject Property Sub-property Type Description Note Accuracy Integrity Orig. Type Pub. Res. Chart Res. ATS airspace Airspace of defined dimensions, alphabetically designated, within which specific types of flights may operate, and for which ATS and air traffic rules of operation are specified Type Text Type of ATS airspace in accordance with Appendix 4 to Implementing Regulation (EU) No 923/2012 (SERA) Designation Text The designator given to the airspace by a responsible authority Lateral limits Polygon The surface defining the horizontal shape of the airspace See Note 1 Vertical limits Upper limit Altitude The upper limit of the airspace Lower limit Altitude The lower limit of the airspace 50 m Routine Calculated 50 m or 100 ft 50 m or 100 ft Class of airspace Code list A categorisation of airspace which determines the operating rules, flight requirements and services provided. Transition altitude Altitude The altitude at or below which the vertical position of aircraft is controlled by reference to altitudes Hours of applicability Schedule The hours of applicability of the airspace ATS unit Unit providing service Name Text The name of the unit providing the service Call sign Text The call sign of the aeronautical station serving the unit Language Code list Information on the language(s) used, specifying area and conditions, as well as when and where to be used, if applicable Applicability Text Information on the area and conditions when to be used Hours of service Schedule Operational hours of the station serving the unit Frequency Value Value The frequency of the ATS airspace Purpose Text Indications for specific purposes of the frequency Note 1 FIR, UIR 2 km Routine Declared 1 min As plotted TMA, CTA 100 m Essential Calculated 1 sec As plotted Controlled traffic region (CTR) 100 m Essential Calculated 1 sec As plotted Subject Property Sub-property Type Description Note Accuracy Integrity Orig. Type Pub. Res. Chart Res. Special-activity airspace Type Code list Type of the special-activity airspace (see Note 1) Identification Text The identification given to uniquely identify the airspace Name Text The name given to the airspace by an authority nominated by the Member State Lateral limits Polygon The surface defining the horizontal shape of the airspace See Note 2 for P, R, and D areas only Vertical limits Upper limit Altitude The upper limit of the airspace Lower limit Altitude The lower limit of the airspace Restriction Text Type of restriction or nature of hazard Activation Text Information on system and means of activation announcements together with information pertinent to civil flights and applicable to air defence identification zone (ADIZ) procedures Time of activity Schedule Time interval when the special activity takes place Risk of interception Text Risk of interception in the event of penetration Note 1 type Prohibited area Note 2 100 m Essential Calculated 1 sec As plotted Restricted area 2 km Routine Declared 1 min As plotted Danger area Military exercise area Military training area ADIZ Other Subject Property Sub-property Type Description Note Accuracy Integrity Orig. Type Pub. Res. Chart Res. Other regulated airspace Type Text Type of airspace (reduced vertical separation minima (RVSM), emergency locator transmitter (ELT), etc.) Identification Text The identification given to uniquely identify the airspace Name Text The name given to the airspace by an authority nominated by the Member State Lateral limits Polygon The surface defining the horizontal shape of the airspace Vertical limits Upper limit Altitude The upper limit of the airspace Lower limit Altitude The lower limit of the airspace Restriction Text Type of restriction, if any Activation Text Information on system and means of activation announcements together with information pertinent to civil flights and applicable to ADIZ procedures Time of activity Schedule Time interval when the special activity takes place Subject Property Sub-property Type Description Note Accuracy Integrity Orig. Type Pub. Res. Chart Res. ATS control sector Identification Text The identification given to the sector Lateral limits Polygon The surface defining the horizontal shape of the ATC sector Vertical limits Upper limit Altitude The upper limit of the sector Lower limit Altitude The lower limit of the sector 3. ATS and other routes data Subject Property Sub-property Type Description Note Accuracy Integrity Orig. Type Pub. Res. Chart Res. ATS route A specified route designed for channelling the flow of traffic as necessary for the provision of ATS Designator Text Designators for ATS routes in accordance with Annex XI (Part-FPD) to this Regulation Designator prefix Text The prefix of the route designator as specified in Note1 Other route A specified route designed for channelling the flow of traffic as necessary without provision of ATS Designator Text Designator of the route Type Text Type of route (e.g. VFR uncontrolled navigation routes) Flight rules Code list Information on the flight rules that apply to the route (IFR/VFR) Route segment From point Reference to the first point of a route segment Name Text The coded designators or code names of a significant point Reporting Code list Indication of the ATS/MET reporting requirement as ‘compulsory’ or ‘on request’ To point Reference to the second point of a route segment Name Text The coded designators or code names of a significant point Reporting Code list Indication of the ATS/MET reporting requirement as ‘compulsory’ or ‘on request’ Track Bearing Track, VOR radial or magnetic bearing of a route segment 1/10 degree (terminal arrival departure) Routine (terminal arrival departure) Calculated (terminal arrival departure) 1 degree (terminal arrival departure) 1 degree (terminal arrival departure) Change over point Point The point at which an aircraft navigating on an ATS route segment defined by reference to the VOR ranges is expected to transfer its primary navigation reference from the facility behind it to the next facility ahead of it In case of a VOR radial Length Distance The geodesic distance between ‘from point’ and ‘to point’ See Note 2 Upper limit Altitude The upper limit of the route segment Lower limit Altitude The lower limit of the route segment Minimum en-route altitude (MEA) Altitude It is the altitude of an en-route segment that provides adequate reception of relevant navigation facilities and ATS communications, complies with the airspace structure, and provides the required obstacle clearance. 50 m Routine Calculated 50 m or 100 ft 50 m or 100 ft Minimum obstacle clearance altitude (MOCA) Altitude It is the minimum altitude of a defined segment that provides the required obstacle clearance 50 m Routine Calculated 50 m or 100 ft 50 m or 100 ft Minimum flight altitude Altitude Minimum flight altitude 50 m Routine Calculated 50 m or 100 ft 50 m or 100 ft Lateral limits Distance Lateral limits of the route Area minimum altitude (AMA) Altitude It is the minimum altitude to be used under instrument meteorological conditions (IMC), which provides a minimum obstacle clearance within a specified area, normally formed by parallels and meridians. Minimum vectoring altitude (MVA) Altitude MVA Restrictions Text Indication on any area speed and level/altitude restrictions, where established Direction of cruising levels Indication of the direction of the cruising level (even, odd, none (NIL)) Forward Code list Indication of the direction of the cruising level (even, odd, NIL) from the first point to the second point of the route segment Backward Code list Indication of the direction of the cruising level (even, odd, NIL) from the second point to the first point of the route segment Availability Text Information on the route availability Class of airspace Text Classification of airspace which determines the operating rules, flight requirements and services provided Performance-based navigation (PBN) requirements Area navigation based on PBN requirements for aircraft operating along an ATS route, on an instrument approach procedure, or in a designated airspace PBN only Navigation specification(s) Text Designation of the navigation specification(s) applicable to a specified segment or segments; there are two kinds of navigation specifications: (a) required navigation performance (RNP) specification: navigation specification based on area navigation that includes the requirement for performance monitoring and alerting, designated by the prefix RNP, e.g. RNP 4, RNP APCH. (b) Area navigation (RNAV) specification: navigation specification based on area navigation that does not include the requirement for performance monitoring and alerting, designated by the prefix RNAV, e.g. RNAV 5, RNAV 1. Navigation performance requirements Text The navigation accuracy requirement for each PBN (RNAV or RNP) route segment Sensor requirements Text Indication of the sensor requirements including any navigation specification limitations Controlling unit Name Text Name of the unit providing the service Channel Text Operating channel/frequency of the controlling unit Logon address Text A specified code used for data link logon to the controlling ATS unit If applicable Note 1 U = upper Note 2 1/10 km Routine Calculated 1/10 km or 1/10 nm 1 km or 1 nm H = helicopter 1/100 km Essential Calculated 1/100 km or 1/100 nm 1 km or 1 nm S = supersonic T = tacan Other Subject Property Sub-property Type Description Note Accuracy Integrity Orig. Type Pub. Res. Chart Res. Waypoint Identification Text Names, coded designators or code names given to the significant point Position Point Geographical location of the waypoint 100 m Essential Surveyed/ calculated 1 sec 1 sec Formation Navigation aid (navaid) Text The station identification of the VOR/DME reference Bearing Bearing The bearing to the VOR/DME reference if the waypoint is not collocated with it See Note 1 below Distance Distance The distance from the VOR/DME reference if the waypoint is not collocated with it See Note 2 below Note 1 1/10 degree Routine Calculated 1/10 degree 1/10 degree 1/100 degree Essential Calculated 1/100 degree 1/10 degree Calculated Note 2 1/10 km Routine Calculated 1/10 km or 1/10 nm 2/10 km (1/10 nm) 1/100 km Essential Calculated 1/100 km or 1/100 nm 2/10 km (1/10 nm) Subject Property Sub-property Type Description Note Accuracy Integrity Orig. Type Pub. Res. Chart Res. En-route holding A predetermined manoeuvre that keeps the aircraft within the specified airspace while awaiting further clearance Identification Text Identification of the holding procedure Fix Text Identification of the holding-procedure fix 100 m Essential Surveyed/ calculated 1 sec 1 sec Waypoint Point Geographical location of the holding waypoint Inbound track Bearing The inbound track of the holding procedure Turn direction Text Direction of the procedure turn Speed Value Maximum indicated airspeed Level Minimum holding level Altitude Minimum holding level of the holding procedure Maximum holding level Altitude Maximum holding level of the holding procedure Outbound time/distance Value Time/distance value of the holding procedure Controlling unit Name Text Indication of the controlling unit Frequency Value The operating frequency/channel of the controlling unit Special holding entry procedure Text Textual description of the special VOR/DME entry procedure In case an entry radial to a secondary fix at the end of the outbound leg has been established for a VOR/DME holding pattern 4. Instrument flight procedure data Subject Property Sub-property Type Description Note Accuracy Integrity Orig. Type Pub. Res. Chart Res. Procedure Identification Final-approach segment (FAS) guidance Code list The name describing the type of radio navigation aid providing the final approach lateral guidance e.g. ILS, VOR, RNAV, etc. APCH RWY Text The RWY designator of the landing and take-off direction, e.g. 27, 35L, 01R Circling Code list Indication if a procedure is/is not a circling approach APCH Multiple code Text A single-letter suffix, starting with the letter ‘z’, following the radio navigation aid type, shall be used if two or more procedures to the same RWY cannot be distinguished by the radio navigation aid type only, e.g.VOR y RWY 20 or VOR z RWY 20. APCH NS limiter Text Sensor-specific information in case of a use limitation PBN only Name Text Name of the instrument flight procedure Plain- language designation Basic indicator Text The basic indicator shall be the name or code names of the significant point where the standard departure route terminates. SID, STAR Validity indicator Text The validity indicator shall be a number from 1 to 9. SID, STAR Route indicator Text The route indicator shall be one letter of the alphabet. The letters ‘I’ and ‘O’ shall not be used. SID, STAR Visual indication Text Indication if the route has been established for aircraft operating in accordance with VFR VFR only Coded designation Significant Point Text The coded designator or code names of the significant point SID, STAR Validity indicator Text The validity indicator of the procedure SID, STAR Route indicator Text The route indicator of the procedure SID, STAR Procedure type Code list Indication of the type of procedure (departure, arrival, approach, other) PBN or conventional Code list Indication if the procedure is PBN or conventional IFR only Precision type Text The instrument procedure type; instrument approach procedures are classified as follows: (a) non-precision approach (NPA) procedure: an instrument approach procedure that utilises lateral but not vertical guidance. (b) approach procedure with vertical guidance (APV): an instrument procedure that utilises lateral and vertical guidance but does not meet the requirements established for precision-approach and -landing operations. (c) precision approach (PA) procedure: an instrument approach procedure using precision lateral and vertical guidance with minima as determined by the category of operation. APCH Aircraft category Code list Indication of which aircraft categories the procedure is intended for Magnetic variation Value The magnetic variation considered for the procedure design Obstacle clearance altitude/height (OCA/H) OCA/H APCH Aircraft category Code list Aircraft category APCH Approach type Code list Approach type (e.g. straight-in, Cat I, Cat II, LLZ, circling, etc.), or specific navigation aid (e.g. step-down fixes), or a specific navigation specification APCH Altitude Altitude The lowest altitude used in establishing compliance with appropriate obstacle clearance criteria APCH Essential Height Height The lowest height above the elevation of the relevant RWY threshold or the aerodrome elevation, as applicable, used in establishing compliance with appropriate obstacle clearance criteria APCH Essential Decision altitude/height (DA/H) DA/H APCH Aircraft category Code list Aircraft category APCH Approach type Code list Approach type (e.g. straight-in, circling, etc.), or specific navigation aid (e.g. step-down fixes), or a specific navigation specification APCH Altitude Altitude A specified altitude in a 3D instrument approach operation at which a missed approach shall be initiated if the required visual reference to continue the approach is not established APCH Height Height A specified height in a 3D instrument approach operation at which a missed approach shall be initiated if the required visual reference to continue the approach is not established APCH Minimum descent altitude/height (MDA/H) MDA/H APCH Aircraft category Code list Aircraft category APCH Approach type Code list Approach type (e.g. straight-in, circling, etc.), or specific navigation aid (e.g. step-down fixes), or a specific navigation specification APCH Altitude Altitude A specified altitude in a 2D instrument approach operation or circling approach operation below which descent shall not be initiated without the required visual reference APCH Height Height A specified height in a 2D instrument approach operation or circling approach operation below which descent shall not be initiated without the required visual reference APCH Minimum sector altitude (MSA) The lowest altitude that may be used and will provide a minimum clearance of 300 m (1 000 ft) above all objects located in an area contained within a sector of a circle of 46 km (25 nm) radius centred on a radio aid to navigation IFR only Sector start angle Angle Start angle of a sector Sector end angle Angle End angle of a sector Based on fix Text Centre of the MSA Altitude Altitude The minimum altitude for each sector Restrictions Text MSA: the lowest altitude that may be used and will provide a minimum clearance of 300 m (1 000 ft) above all objects located in an area contained within a sector of a circle of 46 km (25 nm) radius centred on a radio aid to navigation. Radius Value The radius of each sector Terminal arrival altitude (TAA) The lowest altitude that will provide a minimum clearance of 300 m (1 000 ft) above all objects located in an arc of a circle defined by a 46 km (25 nm) radius centred on the initial-approach fix (IAF) or, where there is no IAF, on the intermediate-approach fix (IF), delimited by straight lines joining the extremity of the arc to the IF; the combined TAAs associated with an approach procedure shall account for an area of 360 degrees around the IF. APCH or PBN only Reference point Text TAA reference point (IAF or IF) IAF Text TAA IAF reference point IF Text TAA IF reference point Distance to IAF Distance The distance of the TAA area boundary from the IAF Altitude Altitude The terminal arrival altitude value Sector start angle Angle Start angle of a sector (bearing to the TAA reference point) Sector end angle Angle End angle of a sector (bearing to the TAA reference point) Step-down arc Distance Radius of the inner area at a lower altitude. Navigation specification name Text A set of aircraft and flight crew requirements needed to support PBN operations within a defined airspace; there are two kinds of navigation specifications: (a) RNP specifications: navigation specifications based on area navigation that includes the requirement for performance monitoring and alerting, designated by the prefix RNP, e.g. RNP 4, RNP APCH. (b) RNAV specifications: navigation specifications based on area navigation that does not include the requirement for performance monitoring and alerting, designated by the prefix RNAV, e.g. RNAV 5, RNAV 1. PBN only Operating minima Text Aerodrome operating minima: the usability limits of an aerodrome for: (a) take-off, expressed in terms of RVR and/or visibility and, if necessary, cloud conditions; (b) landing in precision approach and landing operations, expressed in terms of visibility and/or RVR and DA/H, as appropriate to the category of the operation; (c) landing in approach and landing operations with vertical guidance, expressed in terms of visibility and/or RVR and DA/H; and (d) landing in non-precision approach and landing operations, expressed in terms of visibility and/or RVR, minimum descent altitude/height (MDA/H) and, if necessary, cloud conditions APCH, DEP Temperature Minimum temperature Value Minimum temperature reference APCH or PBN only Maximum temperature Value Maximum temperature reference APCH or PBN only Remote altimeter source Text Cautionary note indicating the altimetry source APCH Proc Ref datum Text Aerodrome or landing threshold APCH PBN requirements Specific requirements related to a PBN procedure PBN Code list Identification of the navigation specification (RNAV 5, RNP 0.3, etc.) Navigation specification Text Any navigation sensor limitations (global navigation satellite system (GNSS) required) Functional requirements Text Any required functionalities described as options in the navigation specification, that is, not included in the core navigation specification (radio frequency (RF) required) Procedure segment SID, STAR, APCH Start Text Identification of the start point of the segment End Text Identification of the end point, or a description of the end, of the segment End fix functionality Code list Indication if the end fix is a fly-by point (a waypoint that requires a turn to allow tangential interception of the next segment of a route or procedure) or flyover point (a waypoint at which a turn is initiated in order to join the next segment of a route or procedure) PBN End fix role Code list Indication of the role of the end fix missed-approach point (MAPt), IF, IAF, final-approach fix (FAF), missed approach holding fix (MAHF), etc. Procedure altitude/height Altitude/height A specified altitude/height flown operationally above the minimum altitude/height and established to accommodate a stabilised descent at a prescribed-descent gradient/angle in the intermediate/final approach segment Certain segments of SID, STAR, APCH only Essential Minimum obstruction clearance altitude (MOCA) Altitude The minimum altitude of a defined segment, which provides the required obstacle clearance SID, STAR, APCH Distance Distance Geodesic distance to the nearest tenth of a kilometre or of a nautical mile between each successive designated significant point 1/100 km Essential Calculated 1/100 km or 1/100 nm 1 km or 1 nm True bearing Bearing True track to the nearest tenth of a degree between each successive significant point SID, STAR, APCH 1/10 degree Routine Calculated 1/10 degree Magnetic bearing Bearing Magnetic track to the nearest tenth of a degree between each successive significant point SID, STAR, APCH 1/10 degree Routine Calculated 1 degree 1 degree Gradient Value APCH, DEP Speed Value Speed limit at a significant point, expressed in units of 10 kt, as applicable Controlling obstacle APCH, DEP Type Text Indication if the obstacle is lit/unlit, type of obstacle (church/wind turbine, etc.) Position Point Coordinates of the controlling obstacle See Section 6 ‘Obstacle data’. Elevation: Elevation Elevation of the top of the controlling obstacle See Section 6 ‘Obstacle data’ Final-approach segment That segment of an instrument approach procedure in which alignment and descent for landing are accomplished SBAS APCH, GBAS APCH Operation type Text A number indicating the type of the final approach segment (e.g. ‘0’ is coded for a straight-in approach procedure including offset procedures.) Approach performance designator Text A number identifying the type of an approach (‘0’ is used to identify a localizer performance with vertical guidance (LPV) approach procedure and a ‘1’ indicates a Category I approach procedure) SBAS provider Text Identifier of a service provider of a particular satellite-based approach system SBAS only Reference path data selector (RPDS) Text A numerical identifier, unique on a frequency in the broadcast region and used to select the FAS data block GBAS only Reference path identifier (RPI) Text A four-character identifier used to confirm the selection of the correct approach procedure Landing threshold point (LTP) or fictitious threshold point (FTP) LTP/FTP Position Point Latitude and longitude of the LTP/FTP 0.3 m (1 ft) Critical 0.0005" (0.01’) Ellipsoidal height Elevation The height of the LTP/FTP above the WGS-84 ellipsoid 0.25 m Critical 0.1 m Orthometric height Elevation The height of the LTP/FTP as related to the geoid and presented as an MSL elevation Flight path alignment point (FPAP) FPAP Position Point Latitude and longitude of the FPAP 0.3 m (1 ft) Critical 0.0005" (0.01’) Orthometric height Elevation The height of the FPAP as related to the geoid and presented as an MSL elevation Approach threshold crossing height (TCH) Height The designated crossing height of the flight path angle above the LTP (or FTP) 0.5 m Critical Calculated 0.05 m Glide path angle (GPA) Value The angle of the approach path (glide path) with respect to the horizontal plane, defined in accordance with WGS-84 at the LTP/FTP 0.01°m N/a 0.01°m Course width at threshold Value The semi-width of the lateral course width at the LTP/FTP, defining the lateral offset at which the receiver achieves full-scale deflection. N/a Critical 0.25 m Delta length offset Distance The distance from the stop end of the RWY to the FPAP; it defines the location where lateral sensitivity changes to missed-approach sensitivity. N/a N/a 8 m Horizontal alert limit (HAL) Value HAL SBAS only Vertical alert limit (VAL) Value VAL SBAS only FAS data block Text A binary string describing the FAS data block generated with an appropriate software tool; the FAS data block is a set of parameters to identify a single precision approach or an APV and define its associated approach. CRC remainder Text An 8-character hexadecimal representation of the calculated remainder bits, used to determine the integrity of the FAS data block during transmission and storage. Subject Property Sub-property Type Description Note Accuracy Integrity Orig. Type Pub. Res. Chart Res. Procedure fix Identification Text Names, coded designators or code names given to the significant point ATC reporting requirements Text Indication of the ATS/MET reporting requirement as ‘compulsory’, ‘on request’ or ‘NIL’ VFR reporting point Text Bridge or church name VFR Position Point Geographical location of the fix See Note 1 Type Text Indication of the type of the fix, such as navaid, Int, waypoint Formations Navaid Text The station identification of the VOR/DME reference Bearing Bearing The bearing to the VOR/DME reference if the waypoint is not collocated with it See Note 2 Distance Distance The distance from the VOR/DME reference if the waypoint is not collocated with it 1/100 km Essential Calculated 1/100 km or 1/100 nm 2/10 km (1/10 nm) Note 1 100 m Essential Surveyed/calculated 1 sec 1 sec 3 m Essential Surveyed/calculated 1/10 sec 1 sec Note 2 1/10 degree Routine Calculated 1/10 degree 1/10 degree 1/10 degree Essential Calculated 1/10 degree 1/10 degree Subject Property Sub-property Type Description Note Accuracy Integrity Orig. Type Pub. Res. Chart Res. Procedure holding A predetermined manoeuvre that keeps the aircraft within the specified airspace while awaiting further clearance Identification Text Identification of the holding procedure Fix Point Geographical location that serves as a reference for a holding procedure Same as the procedure fix Inbound course Course Inbound true course 1/10 degree Outbound course Course Outbound true course 1/10 degree Leg distance Distance Outbound distance of the leg 1/10 km or 1/10 nm Leg time Value Outbound time of the leg Limiting radial Angle Limiting radial from the VOR/DME on which the holding is based Turn direction Value Direction of the procedure turn Minimum altitude Altitude Minimum holding level to the nearest higher (50 m or 100 ft)/flight level 50 m Routine Calculated 50 m or 100 ft/flight level Maximum altitude Altitude Maximum holding level to the nearest higher (50 m or 100 ft)/flight level 50 m or 100 ft/flight level Speed Value Maximum indicated air speed 10 kt Magnetic variation Angle Angle The magnetic variation of the radio navigation aid of the procedure Date Date The date on which the magnetic variation had the corresponding value Navigation specifications name Text Name of the navigation specification – set of aircraft and aircrew requirements needed to support a navigation application within a defined airspace concept RNAV/RNP Subject Property Sub-property Type Description Note Accuracy Integrity Orig. Type Pub. Res. Chart Res. Helicopter procedure specifics Helicopter procedure title (RNAV 263) Text Identification of the helicopter procedure Heliport crossing height (HCH) Height Heliport crossing height Essential 1 m or 1 ft 1 m or 1 ft Initial departure fix (IDF) Point Initial departure fix DEP Missed-approach point (MAPt) Point MAPt APCH Direct visual segment For PinS APP: the portion of flight that connects directly the PinS to the landing location; for PinS DEP: the portion of flight that connects directly the landing location to the IDF Track Line Distance Distance Bearing Angle Crossing height Height Manoeuvring visual segment (VS) PinS VS protected for the following manoeuvres: (a) for PinS APCH: visual manoeuvre from the MAPt around the heliport or landing location to land from a direction other than directly from the MAPt; and (b) for PinS DEP: take-off in a direction other than directly to the IDF, followed by a visual manoeuvre to join the instrument segment at the IDF APCHDEP Centre line Angle Centre line of the take-off climb surface DEP Manoeuvring area Polygon Area where the pilot is expected to manoeuvre visually APCH DEP No manoeuvring area Polygon Area where manoeuvring is prohibited APCH DEP Ingress tracks Line PinS VS protected for the following manoeuvres: (a) for PinS APCH: visual manoeuvre from the MAPt around the heliport or landing location to land from a direction other than directly from the MAPt; and (b) for PinS DEP: take-off in a direction other than directly to the IDF, followed by a visual manoeuvre to join the instrument segment at the IDF APCH DEP HAS Height above the surface diagram APCH Radius Distance Height above surface Height ‘Proceed visually’ text Text Text indicating that the procedure has a ‘Proceed visually’ instruction ‘Proceed VFR’ text Text Text indicating that the procedure has a ‘Proceed VFR’ instruction Visual segment descent angle (VSDA) Value VSDA Ingress tracks Length Distance Width Distance Bearing Angle Subject Property Sub-property Type Description Note Accuracy Integrity Orig. Type Pub. Res. Chart Res. AITF Notes on charts (aeronautical information in textual format) Non-aligned between instrument and visual slope indications Text Missed-approach description Text Missed-approach description of the procedure SID/STAR route description Text Textual description of the SID or STAR procedure Missed-approach climb gradient Value The value of the missed-approach climb gradient of the approach procedure CAT H note Text CAT D large Text Authorisation required (AR) Text Indication that RNP AR Units of measurement Text GNSS in lieu of Communication failure Text Communication failure description Surveillance/radar required SID close-in obstacle note Text Indication wherever close-in obstacles exist which were not considered in the determination of the published-procedure design gradient Offset alignment PDG greater than 3 % 5. Radio navigation aids/systems data Subject Property Sub-property Type Description Note Accuracy Integrity Orig. Type Pub. Res. Chart Res. Radio navigation aid Type Text Type of the radio navigation aid Identification Text The code assigned to uniquely identify the navaid Name Text The textual name assigned to the navaid ILS facility classification Code list A classification based on the functional and performance capabilities of an ILS ILS GBAS facility classification Code list A classification based on the functional and performance capabilities of the GBAS ground subsystem GBAS GBAS approach facility designation Code list A classification based on the GBAS service volume and performance requirements for each supported approach GBAS Area of operation Text Indication whether navigation aid serves en-route (E), aerodrome (A) or dual (AE) purposes Aerodrome/heliport served Text The ICAO location indicator or name of the aerodromes/heliports served RWY served Text Designator of the RWY served Operating entity Text Name of the operating entity of the facility Type of supported operations Code list Indication of the type of supported operation for ILS/MLS, basic GNSS, satellite-based augmentation system (SBAS), and ground-based augmentation system (GBAS) Collocation Text Information that a navaid is collocated with another navaid Hours of operation Schedule The hours of operation of the radio navigation aid Magnetic variation The angular difference between the true north and the magnetic north Angle Angle The magnetic variation at the radio navigation aid ILS/NDB See Note 1 below Date Date The date on which the magnetic variation had the corresponding value Station declination Angle An alignment variation of the navaid between the zero-degree radial and the true north, determined at the time the station is calibrated VOR/ILS/MLS Zero bearing direction Text Direction of the ‘zero bearing’ provided by the station, e.g. magnetic north, true north, etc. VOR Frequency Value Frequency or tuning frequency of the radio navigation aid Channel Text The channel number of the radio navigation aid DME or GBAS Position Point Geographical location of the radio navigation aid See Note 2 below Elevation Elevation The elevation of the transmitting antenna of the DME or the elevation of the GBAS reference point DME or GBAS See Note 3 below Ellipsoidal height Height The ellipsoidal height of the GBAS reference point GBAS Localiser alignment Bearing Bearing The localiser course ILS localiser 1/100 degree Essential Surveyed 1/100 degree (if true) 1 degree Type Text The type of localiser alignment, true or magnetic ILS localiser Zero azimuthal alignment Bearing MLS zero azimuthal alignment MLS 1/100 degree Essential Surveyed 1/100 degree (if true) 1 degree Angle Angle The angle of the glide path of an ILS or the normal glide path angle of an MLS installation ILS GP/MLS RDH Value The value of the ILS reference datum height (ILS RDH) ILS GP 0,5 m Critical Calculated Localiser antenna to RWY end distance Distance ILS localiser —RWY/FATO end distance ILS localiser 3 m Routine Calculated 1 m or 1 ft As plotted ILS glideslope antenna to TRSH distance Distance ILS glideslope antenna — threshold distance along the centre line ILS GP 3 m Routine Calculated 1 m or 1 ft As plotted ILS marker to TRSH distance Distance ILS marker — threshold distance ILS 3 m Essential Calculated 1 m or 1 ft 2/10 km (1/10 nm) ILS DME antenna to TRSH distance Distance ILS DME antenna — threshold distance along the centre line ILS 3 m Essential Calculated 1 m or 1 ft As plotted MLS azimuthal antenna to RWY end distance Distance MLS azimuthal antenna — RWY/FATO end distance MLS 3 m Routine Calculated 1 m or 1 ft As plotted MLS elevation antenna to TRHS distance Distance MLS elevation antenna — threshold distance along the centre line MLS 3 m Routine Calculated 1 m or 1 ft As plotted MLS DME antenna to TRHS distance Distance MLS DME/P antenna — threshold distance along the centre line MLS 3 m Essential Calculated 1 m or 1 ft As plotted Signal polarisation Code list GBAS signal polarisation (GBAS/H or GBAS/E) GBAS Designated operational coverage (DOC) Text DOC or standard service volume (SSV) as range or service volume radius from the navaid/GBAS reference point, height and sectors, if required Note 1 ILS Localiser 1 degree Essential Surveyed 1 degree NDB 1 degree Routine Surveyed 1 degree Surveyed Note 2 Aerodrome navaid 3 m Essential Surveyed 1/10 sec As plotted GBAS reference point 1 m Surveyed En-route 100 m Essential Surveyed 1 sec Surveyed Note 3 DME 30 m (100 ft) Essential Surveyed 30 m (100 ft) 30 m (100 ft) DME/P 3 m Essential Surveyed 3 m (10 ft) GBAS reference point 0,25 m Essential 1 m or 1 ft Subject Property Sub-property Type Description Note Accuracy Integrity Orig. Type Pub. Res. Chart Res. GNSS A worldwide position and time determination system that includes one or more satellite constellations, aircraft receivers and system integrity monitoring, augmented as necessary to support the required navigation performance for the intended operation Name Text The name of the GNSS element (GPS, GBAS, GLONASS, EGNOS, MSAS, WAAS, etc.) Frequency Value Frequency of the GNSS As appropriate Service area Polygon Geographical location of the GNSS service area Coverage area Polygon Geographical location of the GNSS coverage area Operating authority Text Name of the operating authority of the facility Subject Property Sub-property Type Description Note Accuracy Integrity Orig. Type Pub. Res. Chart Res. Aeronautical ground lights Ground lights and other light beacons designating geographical positions that are selected by the Member State as being significant Type Text Type of beacon Designator Text The code assigned to uniquely identify the beacon Name Text The name of the city or town or other identification of the beacon Intensity Value Intensity of the light of the beacon 1000 cd Characteristics Text Information about the characteristics of the beacon Hours of operations Schedule The hours of operation of the beacon Position Point Geographical location of the beacon Marine lights Position Point Geographical location of the beacon Visibility range Distance The visibility range of the beacon Characteristics Text Information about the characteristics of the beacon Subject Property Sub-property Type Description Note Accuracy Integrity Orig. Type Pub. Res. Chart Res. Special navigation system Stations associated with special navigation systems (DECCA, LORAN, etc.) Type Text Type of service available (master signal, slave signal, colour) Designator Text The code assigned to uniquely identify the special navigation system Name Text The textual name assigned to the special navigation system Frequency Value Frequency (channel number, basic pulse rate, recurrence rate, as applicable) of the special navigation system Hours of operations Schedule The hours of operation of the special navigation system Position Point Geographical location of the special navigation system 100 m Essential Surveyed/calculated Operating entity Text Name of the operating entity of the facility Facility coverage Text Description of the special navigation system facility coverage 6. Obstacle data Subject Property Sub-property Type Description Note Accuracy Integrity Orig. Type Pub. Res. Chart Res. Obstacle All fixed (whether temporary or permanent) and mobile obstacles or parts thereof Obstacle identifier Text Unique identifier of the obstacle Operator/owner Text Name and contact information of the obstacle operator or owner Geometry type Code list An indication whether the obstacle is a point, line or polygon Horizontal position Point or line or polygon Horizontal position of the obstacle See Note 1 below Horizontal extent Distance Horizontal extent of the obstacle Elevation Elevation Elevation of the highest point of the obstacle See Note 2 below Height Height Height of the obstacle above ground Type Text Type of obstacle Date and time stamp Date Date and time the obstacle was created Operations Text Feature operations of the mobile obstacles Effectivity Text Effectivity of temporary types of obstacles Lighting Type Text Type of lighting Colour Text Colour of the obstacle lighting Marking Text Type of obstacle marking Material Text Predominant surface material of the obstacle Note 1 Obstacles in Area 1 50 m Routine Surveyed 1 sec As plotted Obstacles in Area 2 (including 2a, 2b, 2c, 2d, take-off flight path area, and obstacle limitation surfaces) 5 m Essential Surveyed 1/10 sec 1/10 sec Obstacles in Area 3 0.5 m Essential Surveyed 1/10 sec 1/10 sec Obstacles in Area 4 2.5 m Essential Surveyed Note 2 Obstacles in Area 1 30 m Routine Surveyed 1 m or 1 ft 3 m (10 ft) Obstacles in Area 2 (including 2a, 2b, 2c, 2d, take-off flight path area, and obstacle limitation surfaces) 3 m Essential Surveyed 1 m or 1 ft 1 m or 1 ft Obstacles in Area 3 0.5 m Essential Surveyed 0.1 m or 0.1 ft or 0.01 m 1 m or 1 ft Obstacles in Area 4 1 m Essential Surveyed 0.1 m 7. Geographic data Subject Property Sub-property Type Description Note Accuracy Integrity Orig. Type Pub. Res. Chart Res. Buildings Buildings (of operational significance) and other salient/prominent (aerodrome) features Name Text Name of the building Geometry Polygon Geographical location of the building Built-up areas Areas covered by cities, towns and villages Name Text Name of the built-up area Geometry Point/polygon Geographical location of the built-up area Railroads All railroads having landmark value Name Text Name of the railroad Geometry Line Geographical location of the railroads Highways and roads All highways and roads having landmark value Name Text Name of highways and roads Geometry Line Geographical location of highways and roads Landmarks Natural and cultural landmarks, such as bridges, prominent transmission lines, permanent cable car installations, wind turbines, mine structures, forts, ruins, levees, pipelines, rocks, bluffs, cliffs, sand dunes, isolated lighthouses and lightships, when considered to be of importance for visual air navigation Characteristics Text Description of the landmark Geometry Line Geographical location of the railroads Political boundaries International political boundaries Geometry Line Geographical location of the international political boundaries Hydrography All water features comprising shorelines, lakes, rivers and streams (including those non-perennial in nature), salt lakes, glaciers and ice caps Name Text Name of the water feature Geometry Line/polygon Geographical location of the water feature Wooded areas Wooded areas Geometry Polygon Geographical location of the wooded area Subject Property Sub-property Type Description Note Accuracy Integrity Orig. Type Pub. Res. Chart Res. Service roads Part of the aerodrome surface used by service vehicles Geometry Polygon Geographical location of the service roads Feature base Text Identification of the feature type affected Identifier base Text Name of the underlying TWY, parking stand area or apron Construction area Part of the aerodrome area under construction Geometry Polygon Geographical location of the construction area Area unsuitable for aircraft movement Areas unsuitable for aircraft movement Geometry Polygon Depicted movement area permanently unsuitable for aircraft and clearly identified as such Survey control point A monumented survey control point Identifier number Text Special unique identifier permanently assigned to a feature instance by the data provider Location Point Geographical location of the survey control point Elevation Elevation Elevation of the survey control point Aerodrome surface routing network (ASRN) node A vertex in a graph defining the ASRN Identifier network Text Logical name comprised of a delimited list of names for one or more features associated with the ASRN feature Identifier threshold Text Name of the feature instance Identifier number Text Special unique identifier permanently assigned to a feature instance by a data provider Term ref Text Terminal building associated with the feature instance Node type Text Type of node Cat stop Text Low-visibility operation category of the holding position Position Point Geographical location of the ASRN node ASRN edge A connection between the nodes in a graph, which defines the ASRN Identifier network Text Logical name comprised of a delimited list of names for one or more features associated with the ASRN feature Direction Text One-way or two-way directionality of the corresponding feature instance Node1 ref Text The identifier number of the ASRN node corresponding to the start point of the edge geometry Node2 ref Text The identifier number of the ASRN node corresponding to the end point of the edge geometry Edge type Text Type of edge Edge derv Text Derivation method of the edge geometry Geometry Line Geographical location of the ASRN edge Data types referred to in column 4 ‘Type’ Type Description Data items Point A pair of coordinates (latitude and longitude) referenced to the mathematical ellipsoid, which define the position of the point on the surface of the Earth Latitude Longitude Horizontal reference system Units of measurement Horizontal accuracy achieved Line Sequence of points defining a linear object Sequence of points Polygon Sequence of points forming the boundary of the polygon; the first and last point are identical Closed sequence of points Height The vertical distance of a level, point or an object, considered as a point, measured from a specific datum Numerical value Vertical reference system Units of measurement Vertical accuracy achieved Altitude The vertical distance of a level, point or an object, considered as a point, measured from the MSL Numerical value Vertical reference system Units of measurement Vertical accuracy achieved Elevation The vertical distance of a point or a level on, or affixed to, the surface of the Earth, measured from the MSL Numerical value Vertical reference system Units of measurement Vertical accuracy achieved Distance A linear value Numerical value Units of measurement Accuracy achieved Angle/bearing An angular value Numerical value Units of measurement Accuracy achieved Value Any measured, declared or derived value not listed above Numerical value Units of measurement Accuracy achieved Date A calendar date referencing a particular day or month Text Schedule A repetitive time period, composed of one or more intervals or special dates (e.g. holidays) occurring cyclically Text Code list A set of predefined text strings or values Text Text Free text String of characters without constraints