Commission Implementing Regulation (EU) 2018/2066 of 19 December 2018 on the monitoring and reporting of greenhouse gas emissions pursuant to Directive 2003/87/EC of the European Parliament and of the Council and amending Commission Regulation (EU) No 601/2012 (Text with EEA relevance.)
Annex IIANNEX II
In force · version of May 27, 2025
Tier definitions for calculation-based methodologies related to installations (Article 12(1))
1. DEFINITION OF TIERS FOR ACTIVITY DATA
The uncertainty thresholds in Table 1 shall apply to tiers relevant to activity data requirements in accordance with point (a) of Article 28(1) and the first subparagraph of Article 29(2), and Annex IV, of this Regulation. The uncertainty thresholds shall be interpreted as maximum permissible uncertainties for the determination of source streams over a reporting period.
Where Table 1 does not include activities listed in Annex I to Directive 2003/87/EC and the mass balance set out in Article 25 of this Regulation is not applied, the operator shall use the tiers listed in Table 1 under ‘Combustion of fuels and fuels used as process input’ for those activities.
Table 1 Tiers for activity data (maximum permissible uncertainty for each tier) Activity/source stream type Parameter to which the uncertainty is applied Tier 1 Tier 2 Tier 3 Tier 4 Combustion of fuels and fuels used as process input Commercial standard fuels Amount of fuel [t] or [Nm 3 ] ± 7,5 % ± 5 % ± 2,5 % ± 1,5 % Other gaseous and liquid fuels Amount of fuel [t] or [Nm 3 ] ± 7,5 % ± 5 % ± 2,5 % ± 1,5 % Solid fuels, excluding waste Amount of fuel [t] ± 7,5 % ± 5 % ± 2,5 % ± 1,5 % Waste Amount of fuel [t] ± 7,5 % ± 5 % ± 2,5 % ± 1,5 % Flaring Amount of flare gas [Nm 3 ] ± 17,5 % ± 12,5 % ± 7,5 % Scrubbing: carbonate (Method A) Amount carbonate consumed [t] ± 7,5 % Scrubbing: gypsum (Method B) Amount gypsum produced [t] ± 7,5 % Scrubbing: urea Amount urea consumed ± 7,5 % Refining of oil Catalytic cracker regeneration ( *1 ) Uncertainty requirements apply separately for each emission source ± 10 % ± 7,5 % ± 5 % ± 2,5 % Production of coke Mass balance methodology Each input and output material [t] ± 7,5 % ± 5 % ± 2,5 % ± 1,5 % Metal ore roasting and sintering Carbonate input and process residues Carbonate input material and process residues [t] ± 5 % ± 2,5 % Mass balance methodology Each input and output material [t] ± 7,5 % ± 5 % ± 2,5 % ± 1,5 % Production of iron and steel Fuel as process input Each mass flow into and from the installation [t] ± 7,5 % ± 5 % ± 2,5 % ± 1,5 % Mass balance methodology Each input and output material [t] ± 7,5 % ± 5 % ± 2,5 % ± 1,5 % Production of cement clinker Kiln input based (Method A) Each relevant kiln input [t] ± 7,5 % ± 5 % ± 2,5 % Clinker output (Method B) Clinker produced [t] ± 5 % ± 2,5 % CKD CKD or bypass dust [t] n.a. ( *2 ) ± 7,5 % Non-carbonate carbon Each raw material [t] ± 15 % ± 7,5 % Production of lime and calcination of dolomite and magnesite Carbonates and other process materials (Method A) Each relevant kiln input [t] ± 7,5 % ± 5 % ± 2,5 % Alkali earth oxide (Method B) Lime produced [t] ± 5 % ± 2,5 % Kiln dust (Method B) Kiln dust [t] n.a. ( *2 ) ± 7,5 % Manufacture of glass and mineral wool Carbonates and other process materials (input) Each carbonate raw material or additives associated with CO 2 emissions [t] ± 2,5 % ± 1,5 % Manufacture of ceramic products Carbon inputs (Method A) Each carbonate raw material or additive associated with CO 2 emissions [t] ± 7,5 % ± 5 % ± 2,5 % Alkali oxide (Method B) Gross production including rejected products and cullet from the kilns and shipment [t] ± 7,5 % ± 5 % ± 2,5 % Scrubbing Dry CaCO 3 consumed [t] ± 7,5 % Production of pulp and paper Make up chemicals Amount of CaCO 3 and Na 2 CO 3 [t] ± 2,5 % ± 1,5 % Production of carbon black Mass balance methodology Each input and output material [t] ± 7,5 % ± 5 % ± 2,5 % ± 1,5 % Production of ammonia Fuel as process input Amount fuel used as process input [t] or [Nm 3 ] ± 7,5 % ± 5 % ± 2,5 % ± 1,5 % Production of hydrogen and synthesis gas Fuel as process input Amount fuel used as process input for hydrogen production [t] or [Nm 3 ] ± 7,5 % ± 5 % ± 2,5 % ± 1,5 % Mass balance methodology Each input and output material [t] ± 7,5 % ± 5 % ± 2,5 % ± 1,5 % Production of bulk organic chemicals Mass balance methodology Each input and output material [t] ± 7,5 % ± 5 % ± 2,5 % ± 1,5 % Production or processing of ferrous and non-ferrous metals, including secondary aluminium Process emissions Each input material or process residue used as input material in the process [t] ± 5 % ± 2,5 % Mass balance methodology Each input and output material [t] ± 7,5 % ± 5 % ± 2,5 % ± 1,5 % Primary aluminium or alumina production Mass balance methodology Each input and output material [t] ± 7,5 % ± 5 % ± 2,5 % ± 1,5 % PFC emissions (slope method) primary aluminium production in [t], anode effect minutes in [number anode effects/cell day] and [anode effect minutes/ occurrence] ± 2,5 % ± 1,5 % PFC emissions (overvoltage method) primary aluminium production in [t], anode effect overvoltage [mV] and current efficiency [-] ± 2,5 % ± 1,5 % CO 2 capture, transfer and geological storage in storage site permitted under Directive 2009/31/EC Mass balance of CO 2 transferred CO 2 transferred into or out from an installation, transport infrastructure or storage site, vented, leaked or fugitive emissions [t] ± 7,5 % ± 5 % ± 2,5 % ± 1,5 % CO 2 venting, leakage, and fugitive emissions CO 2 vented, leaked or from fugitive emissions [t] ± 17,5 % ± 12,5 % ± 7,5 % ( *1 ) For monitoring emissions from catalytic cracker regeneration (other catalyst regeneration and flexi-cokers) in mineral oil refineries, the required uncertainty is related to the total uncertainty of all emissions from that source. ( *2 ) Amount [t] of CKD or bypass dust (where relevant) leaving the kiln system over a reporting period estimated using industry best practice guidelines.
2. DEFINITION OF TIERS FOR CALCULATION FACTORS FOR COMBUSTION EMISSIONS
Operators shall monitor CO 2 emissions from all types of combustion processes taking place under all activities as listed in Annex I to Directive 2003/87/EC or included in the Union system under Article 24 of that Directive using the tier definitions laid down in this section. Where fuels or combustible materials which give rise to CO 2 emissions are used as a process input, section 4 of this Annex shall apply. Where fuels form part of a mass balance in accordance with Article 25(1) of this Regulation, the tier definitions for mass balances in section 3 of this Annex apply.
For process emissions from related exhaust gas scrubbing tier definitions according to sections 4 and 5 of this Annex shall be used, as applicable.
2.1 Tiers for emission factors
Where a biomass fraction, or RFNBO or RCF fraction or synthetic low-carbon fraction is determined for a mixed fuel or material, the tiers defined shall relate to the preliminary emission factor. For fossil fuels and materials, the tiers shall relate to the emission factor.
Tier 1: The operator shall apply one of the following:
(a) the standard factors listed in section 1 of Annex VI;
(b) other constant values in accordance with point (e) of Article 31(1), where no applicable value is contained in section 1 of Annex VI.
Tier 2a: The operator shall apply country specific emission factors for the respective fuel or material in accordance with points (b) and (c) of Article 31(1) or values in accordance with point (d) of Article 31(1).
Tier 2b: The operator shall derive emission factors for the fuel based on one of the following established proxies, in combination with an empirical correlation as determined at least once per year in accordance with Articles 32 to 35 and 39:
(a) density measurement of specific oils or gases, including those common to the refinery or steel industry;
(b) net calorific value for specific coal types.
The operator shall ensure that the correlation satisfies the requirements of good engineering practice and that it is applied only to values of the proxy which fall into the range for which it was established.
Tier 3: The operator shall apply one of the following:
(a) determination of the emission factor in accordance with the relevant provisions of Articles 32 to 35;
(b) the empirical correlation as specified for Tier 2b, where the operator demonstrates to the satisfaction of the competent authority that the uncertainty of the empirical correlation does not exceed 1/3 of the uncertainty value to which the operator has to adhere with regard to the activity data determination of the relevant fuel or material.
2.2 Tiers for net calorific value (NCV)
Tier 1: The operator shall apply one of the following:
(a) the standard factors listed in section 1 of Annex VI;
(b) other constant values in accordance with point (e) of Article 31(1), where no applicable value is contained in section 1 of Annex VI.
Tier 2a: The operator shall apply country specific factors for the respective fuel in accordance with point (b) or (c) of Article 31(1) or values in accordance with point (d) of Article 31(1).
Tier 2b: For commercially traded fuels the net calorific value as derived from the purchasing records for the respective fuel provided by the fuel supplier shall be used provided it has been derived based on accepted national or international standards.
Tier 3: The operator shall determine the net calorific value in accordance with Article 32 to 35.
2.3 Tiers for oxidation factors
Tier 1: The operator shall apply an oxidation factor of 1.
Tier 2: The operator shall apply oxidation factors for the respective fuel in accordance with point (b) or (c) of Article 31(1).
Tier 3: For fuels, the operator shall derive activity-specific factors based on the relevant carbon contents of ashes, effluents and other wastes and by-products, and other relevant incompletely oxidised gaseous forms of carbon emitted except CO. Composition data shall be determined in accordance with Article 32 to 35.
2.4 Tiers for biomass fraction
Tier 1 : The operator shall apply an applicable value published by the competent authority or the Commission, or values in accordance with Article 31(1).
Tier 2 : The operator shall apply an estimation method approved in accordance with the second subparagraph of Article 39(2).
Tier 3a : The operator shall apply analyses in accordance with the first sub-paragraph of Article 39(2), and in accordance with Articles 32 to 35.
Tier 3b : For fuels originating from a production process with defined and traceable input streams, the operator may base the estimation on a material balance of fossil and biomass carbon entering and leaving the process, such as the mass balance system in accordance with Article 30(1) of Directive (EU) 2018/2001.
Where an operator assumes a fossil fraction of 100 % in accordance with Article 39(1) of this Regulation, no tier shall be assigned for the biomass fraction.
2.5 Tiers for RFNBO or RCF fraction or synthetic low-carbon fraction
Tier 1 : The operator shall determine the RFNBO or RCF fraction or synthetic low-carbon fraction based on the mass balance system in accordance with Article 30(1) of Directive (EU) 2018/2001.
Where an operator assumes a fossil fraction of 100% in accordance with Article 39a(1) of this Regulation, no tier shall be assigned for the RFNBO or RCF fraction or synthetic low-carbon fraction.
3. DEFINITION OF TIERS FOR CALCULATION FACTORS FOR MASS BALANCES
Where an operator uses a mass balance in accordance with Article 25, it shall use the tier definitions of this section.
3.1 Tiers for carbon content
The operator shall apply one of the tiers listed in this point. For deriving the carbon content from an emission factor, the operator shall use the following equations:
(a) for emission factors expressed as t CO 2 /TJ: C = (EF × NCV) / f
(b) for emission factors expressed as t CO 2 /t: C = EF / f
In those formulae, C is the carbon content expressed as fraction (tonne carbon per tonne product), EF is the emission factor, NCV is the net calorific value, and f is the factor laid down in Article 36(3).
Where a biomass fraction or RFNBO or RCF fraction or synthetic low-carbon fraction is determined for a mixed fuel or material, the tiers defined shall relate to the total carbon content. The biomass fraction of the carbon shall be determined using the tiers defined in Section 2.4 of this Annex. The RFNBO or RCF fraction or synthetic low-carbon fraction of the carbon shall be determined using the tiers defined in Section 2.5 of this Annex.
Tier 1: The operator shall apply one of the following:
(a) the carbon content derived from standard factors listed in Annex VI sections 1 and 2;
(b) other constant values in accordance with point (e) of Article 31(1), where no applicable value is contained in Annex VI sections 1 and 2.
Tier 2a: The operator shall derive the carbon content from country specific emission factors for the respective fuel or material in accordance with point (b) or (c) of Article 31(1) or values in accordance with point (d) of Article 31(1).
Tier 2b : The operator shall derive the carbon content from emission factors for the fuel based on one of the following established proxies in combination with an empirical correlation as determined at least once per year in accordance with Articles 32 to 35 of this Regulation:
(a) density measurement of specific oils or gases common, for example, to the refinery or steel industry;
(b) net calorific value for specific coals types.
The operator shall ensure that the correlation satisfies the requirements of good engineering practice and that it is applied only to values of the proxy which fall into the range for which it was established.
Tier 3: The operator shall apply one of the following:
(a) determination of the carbon content in accordance with the relevant provisions of Articles 32 to 35;
(b) the empirical correlation as specified for Tier 2b, where the operator demonstrates to the satisfaction of the competent authority that the uncertainty of the empirical correlation does not exceed 1/3 of the uncertainty value to which the operator has to adhere with regard to the activity data determination of the relevant fuel or material.
3.2 Tiers for net calorific values
The tiers defined in section 2.2 of this Annex shall be used.
3.3 Tiers for biomass fraction
The tiers defined in section 2.4 of this Annex shall be used.
3.4 Tiers for RFNBO or RCF fraction or synthetic low-carbon fraction
The tiers defined in Section 2.5 of this Annex shall be used.
4. DEFINITION OF TIERS FOR THE CALCULATION FACTORS FOR CO 2 PROCESS EMISSIONS
For all CO 2 process emissions, in particular for emissions from the decomposition of carbonates and from process materials containing carbon other than in form of carbonates, including urea, coke and graphite, where they are monitored using the standard methodology in accordance with Article 24(2), the tiers defined in this section for the applicable calculation factors shall be applied.
In case of mixed materials which contain inorganic as well as organic forms of carbon, the operator may choose:
— to determine a total preliminary emission factor for the mixed material by analysing the total carbon content, and using a conversion factor and – if applicable – biomass fraction and net calorific value related to that total carbon content; or
— to determine the organic and inorganic contents separately and treat them as two separate source streams.
For emissions from the decomposition of carbonates, the operator may choose for each source stream one of the following methods:
(a) Method A (Input based): The emission factor, conversion factor and activity data are related to the amount of material input into the process.
(b) Method B (Output based): The emission factor, conversion factor and activity data are related to the amount of output from the process.
For other CO 2 process emissions, the operator shall apply only method A.
By way of derogation from the provisions in this section and the following sub-sections, operators may rate process emissions from materials as zero, provided those materials meet all the following conditions:
(i) do not meet the definitions of RFNBOs or RCFs or synthetic low-carbon fuels;
(ii) were produced in another installation covered by Directive 2003/87/EC;
(iii) CO 2 was chemically bound to produce the materials;
(iv) the installation that emitted the CO 2 in point (iii), included this CO 2 in its annual emissions report;
(v) do not meet the specification of a product that is listed in the delegated Regulation adopted pursuant to Article 12(3b) of Directive 2003/87/EC.
4.1. Tiers for the emission factor using Method A
Tier 1: The operator shall apply one of the following:
(a) the standard factors listed in Annex VI section 2 Table 2 in case of carbonate decomposition, or in Tables 1, 4 or 5 for other process materials;
(b) other constant values in accordance with point (e) of Article 31(1), where no applicable value is contained in Annex VI.
Tier 2: The operator shall apply a country specific emission factor in accordance with point (b) or (c) of Article 31(1), or values in accordance with point (d) of Article 31(1).
Tier 3: The operator shall determine the emission factor in accordance with Articles 32 to 35. Stoichiometric ratios as listed in section 2 of Annex VI shall be used to convert composition data into emission factors, where relevant.
4.2. Tiers for the conversion factor using Method A
Tier 1: A conversion factor of 1 shall be used.
Tier 2: Carbonates and other carbon leaving the process shall be considered by means of a conversion factor with a value between 0 and 1. The operator may assume complete conversion for one or several inputs and attribute unconverted materials or other carbon to the remaining inputs. The additional determination of relevant chemical parameters of the products shall be carried out in accordance with Articles 32 to 35.
4.3. Tiers for the emission factor using Method B
Tier 1: The operator shall apply one of the following:
(a) the standard factors listed in Annex VI section 2 Table 3.
(b) other constant values in accordance with point (e) of Article 31(1), where no applicable value is contained in Annex VI.
Tier 2: The operator shall apply a country specific emission factor in accordance with point (b) or (c) of Article 31(1), or values in accordance with point (d) of Article 31(1).
Tier 3: The operator shall determine the emission factor in accordance with Articles 32 to 35. Stoichiometric ratios referred to in Annex VI section 2 Table 3 shall be used to convert composition data into emission factors assuming that all of the relevant metal oxides have been derived from respective carbonates. For this purpose the operator shall take into account at least CaO and MgO, and shall provide evidence to the competent authority as to which further metal oxides relate to carbonates in the raw materials.
4.4. Tiers for the conversion factor using Method B
Tier 1: A conversion factor of 1 shall be used.
Tier 2: The amount of non-carbonate compounds of the relevant metals in the raw materials, including return dust or fly ash or other already calcined materials, shall be reflected by means of conversion factors with a value between 0 and 1 with a value of 1 corresponding to a full conversion of raw material carbonates into oxides. The additional determination of relevant chemical parameters of the process inputs shall be carried out in accordance with Articles 32 to 35.
4.5. Tiers for the net calorific value (NCV)
If relevant, the operator shall determine the net calorific value of the process material using the tiers defined in section 2.2 of this Annex. NCV is considered not relevant for de minimis source streams or where the material is not itself combustible without other fuels being added. If in doubt, the operator shall seek confirmation by the competent authority on whether NCV has to be monitored and reported.
4.6. Tiers for the biomass fraction
If relevant, the operator shall determine the biomass fraction of the carbon contained in the process material, using the tiers defined in section 2.4 of this Annex.
4.7. Tiers for the RFNBO or RCF fraction or synthetic low-carbon fraction
The tiers defined in Section 2.5 of this Annex shall be used.