Commission Directive 81/334/EEC of 13 April 1981 adapting to technical progress Council Directive 70/157/EEC on the approximation of the laws of the Member States relating to the permissible sound level and the exhaust system of motor vehicles
Annex IIANNEX II EEC TYPE-APPROVAL OF EXHAUST SYSTEMS AS SEPARATE TECHNICAL UNITS (REPLACEMENT EXHAUST SYSTEMS)
In force · version of Apr 28, 1981
0.SCOPE
This Annex applies to the type-approval, as separate technical units within the meaning of Article 9a of Directive 70/156/EEC, of exhaust systems or components thereof to be fitted to one or more given types of motor vehicle in categories M1 and N1 as replacement parts.
1.DEFINITIONS 1.1. "Replacement exhaust system or component thereof" means any part of the exhaust system defined in item 1.2.1 of Annex I intended to replace on a vehicle a part of the type granted EEC type-approval with the vehicle in accordance with Annex I.
2.APPLICATION FOR EEC TYPE-APPROVAL 2.1. Application for EEC type-approval in respect of a replacement exhaust system or component thereof as a separate technical unit must be submitted by the vehicle manufacturer of the separate technical unit in question or by their authorized representatives.
2.2. Application for EEC type-approval in respect of each type of replacement exhaust system or component thereof must be accompanied by the undermentioned documents in triplicate and the following information: 2.2.1. - a description of the type(s) of vehicle to which the system or components thereof are to be fitted with reference to the characteristics mentioned in item 1.1 of Annex I. The numbers and/or symbols designating the engine and vehicle type must be indicated;
2.2.2. - a description of the replacement exhaust system indicating the relative position of each system component, together with mounting instructions;
2.2.3. - detailed drawings of each component, so that they can be easily located and identified, and reference to the materials used.
These drawings must indicate the place provided for the compulsory affixing of the EEC type-approval.
2.3. At the request of the technical service concerned, the applicant must submit: 2.3.1. - two examples of the system in respect of which application for EEC type-approval has been made;
2.3.2. - an exhaust system of the type originally fitted to the vehicle when EEC type-approval was granted;
2.3.3. - a vehicle representative of the type to which the system is to be fitted:
- which, as far as its noise level when moving is concerned, must be in such a condition that it respects the limits in item 5.2.2.1 of Annex I and does not exceed by more than 3 dB(A) the values obtained during the type-approval tests and
- which, as far as its noise level when stationary is concerned, respects the value obtained during the type-approval;
2.3.4. - a separate engine corresponding to the type of vehicle described above.
3.MARKINGS 3.1. The replacement exhaust system or its components, excluding fixing hardware and pipes must bear : bear: 3.1.1. - the trade mark or trade name of the manufacturer of the replacement system and its components;
3.1.2. - the manufacturer's commercial description;
3.1.3. - the EEC type-approval number preceded by the distinctive letter(s) of the country granting EEC type-approval (1).
3.2. These marks must be clearly legible and indelible.
4.EEC TYPE-APPROVAL 4.1. If an application within the meaning of item 2.1 is approved, the competent authority will draw up a certificate corresponding to the model shown in Annex IV. The type-approval number must be preceded by the distinctive letter(s) of the country granting EEC type-approval.
5.SPECIFICATIONS 5.1. General specifications 5.1.1. The replacement exhaust system or component thereof must be designed, constructed and capable of being mounted so as to ensure that the vehicle complies with the provisions of this Directive under normal conditions of use, notwithstanding any vibrations to which it may be subject.
5.1.2. The exhaust system or components thereof must be designed, constructed and capable of being mounted so that reasonable resistance to the corrosion phenomena to which it/they is/are exposed is obtained having regard to the conditions of use of the vehicle.
5.2. Specifications relating to sound levels 5.2.1. The acoustic efficiency of the replacement exhaust system or component thereof must be checked using the methods described in items 5.2.2.4 and 5.2.3.4 of Annex I.
When the replacement exhaust system or component thereof is mounted on the vehicle referred to in item 2.3.3 of this Annex, the sound levels obtained using the two methods (stationary and moving vehicle) must satisfy one of the following conditions: 5.2.1.1. they must not exceed the values obtained when this type of vehicle was granted EEC type-approval;
5.2.1.2. they must not exceed the sound level values measured on the vehicle, referred to in item 2.3.3, when this is fitted with an exhaust system of the same type as that fitted to the vehicle when EEC type-approval was granted.
5.3. Measurement of vehicle performance 5.3.1. The replacement exhaust system or components thereof must be such as to ensure that vehicle performance is comparable with that achieved with the original equipment exhaust system or component thereof.
5.3.2. The replacement exhaust system or, depending on the manufacturer's choice, the components of this system must be compared with the original equipment exhaust system or components thereof, which are also in new condition, fitted in turn to the vehicle referred to in item 2.3.3. (1) B = Belgium, D = Federal Republic of Germany, DK = Denmark, F = France, GR = Greece, I = Italy, IRL = Ireland, L = Luxembourg, NL = Netherlands, UK = United Kingdom.
5.3.3. The check must take the form of a measurement of pressure loss under the conditions specified in item 5.3.4.1 or 5.3.4.2. The value measured with the replacement exhaust system must not exceed the value measured with the original equipment system by more than 25 % under the conditions mentioned below.
5.3.4. Test Method 5.3.4.1. Engine test method
The measurement must be conducted on the engine referred to in item 2.3.4 coupled to a dynamometer.
With the throttle completely open, the bench shall be so adjusted as to obtain the engine speed (S) corresponding to the rated maximum power of the engine.
For the measurement of back pressure, the pressure tap must be placed at the distance from the exhaust manifold specified in Figures 1, 2 and 3.
5.3.4.2. Vehicle test method
The measurements must be carried out on the vehicle referred to in item 2.3.3.
The test must be conducted: - either on a road, or
- on a roller dynamometer.
With the throttle completely open, the engine must be loaded so as to obtain the engine speed (S) corresponding to the rated maximum power.
For the measurement of back pressure, the pressure tap must be placed at the distance from the exhaust manifold specified in Figures 1, 2 and 3.
5.4. Additional provisions in respect of exhaust systems or components thereof filled with fibrous materials
Fibrous materials must not be used in the manufacture of replacement exhaust systems or components thereof unless appropriate measures are taken during the design and production stages to ensure that a level of efficiency is attained corresponding to the limits set out in item 5.2.2.1 of Annex I.
Such a silencing system is deemed to be effective in traffic if the exhaust gases are not in contact with the fibrous materials or if, after the removal of the fibrous materials, the sound levels comply with the requirements set out in item 5.2.1 above, when the exhaust system is tested on a vehicle in accordance with the methods described in items 5.2.2 and 5.2.3 of Annex I.
If this condition is not observed, the entire exhaust system must be subjected to conditioning. This must be done using one of the three methods described in items 5.3.1.1, 5.3.1.2 and 5.3.1.3 of Annex I.
After conditioning, the sound level must be checked as specified in item 5.2.1 above.
When the procedure described in item 5.2.1.2 is employed, the applicant for EEC type-approval may ask for the conditioning of the original equipment exhaust system or submit one which has been emptied.
6.CONFORMITY OF PRODUCTION 6.1. Any replacement exhaust system or component thereof bearing an EEC type-approval number pursuant to this Directive must conform to the approved type of exhaust system and comply with the requirements of item 5 above.
6.2. In order to check conformity as required by item 6.1 above, an exhaust system or component thereof bearing the EEC type-approval number must be taken from the series. Production is deemed to conform with the requirements of this Directive if the sound levels measured in accordance with item 5.2 do not exceed the level measured during the EEC type-approval tests of this type of exhaust system or component thereof by more than 1 dB(A).
Back pressure - measuring points
>PIC FILE= "T0029283">