Directive 2004/42/CE of the European Parliament and of the Council of 21 April 2004 on the limitation of emissions of volatile organic compounds due to the use of organic solvents in certain paints and varnishes and vehicle refinishing products and amending Directive 1999/13/EC
Preambolo 1
Directive 2004/42/CE of the European Parliament and of the Council
of 21 April 2004
on the limitation of emissions of volatile organic compounds due to the use of organic solvents in certain paints and varnishes and vehicle refinishing products and amending Directive 1999/13/EC
THE EUROPEAN PARLIAMENT AND THE COUNCIL OF THE EUROPEAN UNION,
Having regard to the Treaty establishing the European Community, and in particular Article 95 thereof,
Having regard to the proposal from the Commission,
Having regard to the Opinion of the European Economic and Social Committee(1),
Acting in accordance with the procedure laid down in Article 251 of the Treaty(2),
Whereas:
HAVE ADOPTED THIS DIRECTIVE:
recital 1recital 1
(1) Directive 2001/81/EC of the European Parliament and the Council of 23 October 2001 on national emission ceilings for certain atmospheric pollutants(3) sets national ceilings for emissions of certain pollutants, including volatile organic compounds (hereinafter: "VOCs"), to be attained by 2010 as part of the Community's integrated strategy to combat acidification and ground-level ozone, but does not include limit values for emissions of those pollutants from specific sources.
recital 2recital 2
(2) In order to comply with the national ceiling for emissions of VOCs, Member States have to target a number of different categories of sources of these emissions.
recital 3recital 3
(3) This Directive complements measures taken at national level in order to ensure compliance with the ceiling for emissions of VOCs.
recital 4recital 4
(4) In the absence of Community provisions, legislation in the Member States imposing limit values for VOCs in certain categories of products might differ. Such disparities, together with the absence of such legislation in some Member States, would be liable to create unnecessary barriers to trade and distortion of competition within the internal market.
recital 5recital 5
(5) National laws and provisions which, for the purposes of combating ground-level ozone, establish limit values for the content of VOCs in the products covered by this Directive therefore need to be harmonised in order to ensure that they do not restrict the free movement of these products.
recital 6recital 6
(6) Since the objective of the proposed action, namely reducing emissions of VOCs, cannot be sufficiently achieved by the Member States, because emissions of VOCs in one Member State affect air quality in other Member States and reductions of VOC emissions can therefore, by reason of the scale and effects of the action, be better achieved at Community level, the Community may adopt measures, in accordance with the principle of subsidiarity as set out in Article 5 of the Treaty. In accordance with the principle of proportionality, as set out in that Article, this Directive does not go beyond what is necessary in order to achieve this objective.
recital 7recital 7
(7) The VOC content of paints, varnishes and vehicle refinishing products gives rise to significant emissions of VOCs into the air, which contribute to the local and transboundary formation of photochemical oxidants in the boundary layer of the troposphere.
recital 8recital 8
(8) The VOC content of certain paints and varnishes and vehicle refinishing products should therefore be reduced as much as is technically and economically feasible taking into account climatic conditions.
recital 9recital 9
(9) A high level of environmental protection requires the setting and achievement of content limit values for VOCs used in products covered by this Directive.
recital 10recital 10
(10) Provision should be made for transitional measures for products produced before the requirements of this Directive come into force.
recital 11recital 11
(11) Member States should be able to grant individual licences for the sale and purchase for specific purposes of products in strictly limited quantities which do not comply with the solvent limit values established by this Directive.
recital 12recital 12
(12) This Directive complements Community provisions on the labelling of chemical substances and preparations.
recital 13recital 13
(13) The protection of the health of consumers and/or workers and the protection of the working environment should not fall within the scope of this Directive, and measures taken by Member States for these purposes should therefore not be affected by this Directive.
recital 14recital 14
(14) Content limit values need to be monitored in order to determine whether the mass concentrations of VOCs found in each category of paints, varnishes and vehicle refinishing products covered by this Directive are within the permitted limits.
recital 15recital 15
(15) As the VOC content of products used for certain vehicle refinishing activities are now regulated under this Directive, Council Directive 1999/13/EC of 11 March 1999 on the limitation of emissions of volatile organic compounds due to the use of organic solvents in certain activities and installations(4) should be amended accordingly.
recital 16recital 16
(16) Member States should, nevertheless, be able to maintain or introduce national measures for the control of emissions from vehicle refinishing activities involving the coating of road vehicles as defined in Council Directive 70/156/EEC of 6 February 1970 on the approximation of the laws of the Member States relating to the type-approval of motor vehicles and their trailers(5), or part of them, carried out as part of vehicle repair, conservation or decoration outside of manufacturing installations.
recital 17recital 17
(17) This Directive should not apply to products sold for exclusive use in installations authorised according to Directive 1999/13/EC where emission limiting measures provide alternative means of achieving at least equivalent VOC emission reductions.
recital 18recital 18
(18) The Member States should lay down rules on penalties applicable to infringements of the provisions of this Directive and ensure that they are implemented. Those penalties should be effective, proportionate and dissuasive.
recital 19recital 19
(19) Member States should report to the Commission on the experience gained in the application of this Directive.
recital 20recital 20
(20) A review should be made both of the scope for reducing the VOC content of products outside the scope of this Directive and the possibility of further reducing the VOC limit values already provided for.
recital 21recital 21
(21) The measures necessary for the implementation of this Directive should be adopted in accordance with Council Decision 1999/468/EC of 28 June 1999 laying down the procedures for the exercise of implementing powers conferred on the Commission(6),
Articolo 1Purpose and scope
1.The purpose of this Directive is to limit the total content of VOCs in certain paints and varnishes and vehicle refinishing products in order to prevent or reduce air pollution resulting from the contribution of VOCs to the formation of tropospheric ozone.
2.To achieve the objective set out in paragraph 1, this Directive approximates the technical specifications for certain paints and varnishes and vehicle refinishing products.
3.This Directive shall apply to the products set out in Annex I.
4.This Directive does not prejudice or affect measures, including labelling requirements, taken at Community or national level to protect the health of consumers and of workers and their working environment.
Articolo 2Definitions
For the purposes of this Directive, the following definitions shall apply:
1.‘Competent authority’means the authority or authorities or bodies responsible under the legal provisions of the Member States for carrying out the obligations arising from this Directive;
2.‘Substances’means any chemical element and its compounds, as they occur in the natural state or as produced by industry, whether in solid or liquid or gaseous form;
3.‘Mixture’ means mixtures or solutions composed of two or more substances;
4.‘Organic compound’means any compound containing at least the element carbon and one or more of hydrogen, oxygen, sulphur, phosphorus, silicon, nitrogen, or a halogen, with the exception of carbon oxides and inorganic carbonates and bicarbonates;
5.‘Volatile organic compound (VOC)’means any organic compound having an initial boiling point less than or equal to 250°C measured at a standard pressure of 101,3 kPa;
6.‘VOC content’means the mass of volatile organic compounds, expressed in grams/litre (g/l), in the formulation of the product in its ready to use condition. The mass of volatile organic compounds in a given product which react chemically during drying to form part of the coating shall not be considered part of the VOC content;
7.‘Organic solvent’means any VOC which is used alone or in combination with other agents to dissolve or dilute raw materials, products, or waste materials, or is used as a cleaning agent to dissolve contaminants, or as a dispersion medium, or as a viscosity adjuster, or as a surface tension adjuster, or as a plasticiser, or as a preservative;
8.‘Coating’means any mixture , including all the organic solvents or mixture containing organic solvents necessary for its proper application, which is used to provide a film with decorative, protective or other functional effect on a surface;
9.‘Film’means a continuous layer resulting from the application of one or more coats to a substrate;
10.‘Water-borne coatings (WB)’means coatings the viscosity of which is adjusted by the use of water;
11.‘Solvent-borne coatings (SB)’means coatings the viscosity of which is adjusted by the use of organic solvent;
12.‘Placing on the market’means making available to third parties, whether in exchange for payment or not. Importation into the Community customs territory shall be deemed to be placing on the market for the purposes of this Directive.
Articolo 3Requirements
1.Member States shall ensure that the products set out in Annex I are placed on the market within their territory after the dates laid down in Annex II only if they have a VOC content not exceeding the limit values set out in Annex II and comply with Article 4.
For determining compliance with the VOC content limit values set out in Annex II, the analytical methods referred to in Annex III shall be used.
For products set out in Annex I to which solvents or other components containing solvents have to be added in order for the product to be ready for use, the limit values in Annex II shall apply to the VOC content of the product in its ready for use condition.
2.By way of derogation from paragraph 1, Member States shall exempt from compliance with the above requirements products sold for exclusive use in an activity covered by Directive 1999/13/EC and carried out in a registered or authorised installation according to Articles 3 and 4 of that Directive.
3.For the purposes of restoration and maintenance of buildings and vintage vehicles designated by competent authorities as being of particular historical and cultural value, Member States may grant individual licences for the sale and purchase in strictly limited quantities of products which do not meet the VOC limit values laid down in Annex II.
4.Products falling under the scope of this Directive which are shown to be produced before the dates laid down in Annex II and do not fulfil the requirements of paragraph 1 may be placed on the market for a period of 12 months following the date on which the requirement applying to the product in question comes into force.
Articolo 4Labelling
Member States shall ensure that the products set out in Annex I carry a label when they are placed on the market. The label shall indicate:
(a) the subcategory of the product and the relevant VOC limit values in g/l as referred to in Annex II;
(b) the maximum content of VOC in g/l of the product in a ready to use condition.
Articolo 5Competent authority
Member States shall designate a competent authority responsible for fulfilling the obligations laid down in this Directive, and shall inform the Commission thereof not later than 30 April 2005.
Articolo 8Free circulation
Member States shall not, on the grounds dealt with in this Directive, prohibit, restrict or prevent the placing on the market of products falling under the scope of this Directive which, in their ready for use condition, comply with the requirements of this Directive.
Articolo 9Review
The Commission is invited to submit to the European Parliament and the Council:
1.by 2008 at the latest, a report based on the results of the review referred to in Article 10 of Directive 2001/81/EC. This report shall examine: (a) the broad scope and potential for making reductions in the VOC content of products outside the scope of this Directive including aerosols for paints and varnishes; (b) the possible introduction of a further (phase II) reduction in the VOC content of vehicle refinishing products; (c) any new element relating to the socio-economic impact of the application of phase II as foreseen for paints and varnishes;
2.at the latest 30 months after the date of implementation of the VOC content limit values of Annex II phase II, a report taking account, in particular, of the reports referred to in Article 7 and of any technological developments in the manufacture of paints, varnishes and vehicle refinishing products. This report shall examine the broad scope and potential for making further reductions in VOC content of products inside the scope of this Directive, including the possible distinction between paints used for interiors and exteriors in subcategories (d) and (e) of Annex I, point 1.1. and Annex II, section A.
These reports shall be accompanied, if appropriate, by proposals to amend this Directive.
Articolo 10Penalties
Member States shall lay down the rules on penalties applicable to infringements of the national provisions adopted pursuant to this Directive and shall take the necessary measures to ensure that they are implemented. The penalties provided for must be effective, proportionate and dissuasive. Member States shall notify those rules and measures to the Commission by 30 October 2005 at the latest, and shall notify it without delay of any subsequent amendment affecting them.
Articolo 11Adaptation to technical progress
The Commission is empowered to adopt delegated acts in accordance with Article 11a amending Annex III to adapt it to technical progress.
Articolo 11aExercise of the delegation
1.The power to adopt delegated acts is conferred on the Commission subject to the conditions laid down in this Article.
2.The power to adopt delegated acts referred to in Article 11 shall be conferred on the Commission for a period of five years from 26 July 2019. The Commission shall draw up a report in respect of the delegation of power not later than nine months before the end of the five-year period. The delegation of power shall be tacitly extended for periods of an identical duration, unless the European Parliament or the Council opposes such extension not later than three months before the end of each period.
3.The delegation of power referred to in Article 11 may be revoked at any time by the European Parliament or by the Council. A decision to revoke shall put an end to the delegation of the power specified in that decision. It shall take effect the day following the publication of the decision in the Official Journal of the European Union or at a later date specified therein. It shall not affect the validity of any delegated acts already in force.
4.Before adopting a delegated act, the Commission shall consult experts designated by each Member State in accordance with the principles laid down in the Interinstitutional Agreement of 13 April 2016 on Better Law-Making ( 1 ).
5.As soon as it adopts a delegated act, the Commission shall notify it simultaneously to the European Parliament and to the Council.
6.A delegated act adopted pursuant to Article 11 shall enter into force only if no objection has been expressed either by the European Parliament or the Council within a period of two months of notification of that act to the European Parliament and the Council or if, before the expiry of that period, the European Parliament and the Council have both informed the Commission that they will not object. That period shall be extended by two months at the initiative of the European Parliament or of the Council.
Articolo 12Committee
1.The Commission shall be assisted by the committee established by Article 13 of Council Directive 1999/13/EC, hereinafter referred to as ‘the Committee’.
2.Where reference is made to this paragraph Articles 5 and 7 of Decision 1999/468/EC shall apply, having regard to the provisions of Article 8 thereof.
The period laid down in Article 5(6) of Decision 1999/468/EC shall be set at three months.
Articolo 13Amendment of Directive 1999/13/EC
1.Directive 1999/13/EC is hereby amended as follows:
in Annex I, in the section entitled ‘Vehicle refinishing’, the following indent shall be deleted:
— ‘— the coating of road vehicles as defined in Directive 70/156/EEC, or part of them, carried out as part of vehicle repair, conservation or decoration outside of manufacturing installations, or’.
2.Notwithstanding paragraph 1, Member States may maintain or introduce national measures for the control of emissions from vehicle-refinishing activities deleted from the scope of Directive 1999/13/EC.
Articolo 14Transposition
1.Member States shall bring into force the laws, regulations and administrative provisions necessary to comply with this Directive by 30 October 2005 at the latest, and shall immediately inform the Commission thereof.
When Member States adopt those provisions, they shall contain a reference to this Directive or be accompanied by such a reference on the occasion of their official publication. Member States shall determine how such reference is to be made.
2.Member States shall communicate to the Commission the text of the provisions of national law which they adopt in the field covered by this Directive, together with a table showing how the provisions of this Directive correspond to the national provisions adopted.
Articolo 15Entry into force of the Directive
This Directive shall enter into force on the day of its publication in the Official Journal of the European Union .
Articolo 16Addressees
This Directive is addressed to the Member States.
Allegato IANNEX I
SCOPE
1.For the purposes of this Directive, paints and varnishes means products listed in the subcategories below, excluding aerosols. They are coatings applied to buildings, their trim and fittings, and associated structures for decorative, functional and protective purpose. 1.1. Subcategories: a) ‘matt coatings for interior walls and ceilings’means coatings designed for application to indoor walls and ceilings with a degree of gloss ≤ 25@60°. b) ‘glossy coatings for interior walls and ceilings’means coatings designed for application to indoor walls and ceilings with a degree of gloss > 25@60°. c) ‘coatings for exterior walls of mineral substrate’means coatings designed for application to outdoor walls of masonry, brick or stucco; d) ‘interior/exterior trim and cladding paints for wood, metal or plastic’means coatings designed for application to trim and cladding which produce an opaque film. These coatings are designed for either a wood, metal or a plastic substrate. This subcategory includes undercoats and intermediate coatings; e) ‘interior/exterior trim varnishes and woodstains’means coatings designed for application to trim which produce a transparent or semi-transparent film for decoration and protection of wood, metal and plastics. This subcategory includes opaque woodstains. Opaque woodstains means coatings producing an opaque film for the decoration and protection of wood, against weathering, as defined in EN 927-1, within the semi-stable category; f) ‘minimal build woodstains’means woodstains which, in accordance with EN 927-1:1996, have a mean thickness of less than 5μm when tested according to ISO 2808: 1997, method 5A; g) ‘primers’means coatings with sealing and/or blocking properties designed for use on wood or walls and ceilings; h) ‘binding primers’means coatings designed to stabilise loose substrate particles or impart hydrophobic properties and/or to protect wood against blue stain; i) ‘one-pack performance coatings’means performance coatings based on film-forming material. They are designed for applications requiring a special performance, such as primer and topcoats for plastics, primer coat for ferrous substrates, primer coat for reactive metals such as zinc and aluminium, anticorrosion finishes, floor coatings, including for wood and cement floors, graffiti resistance, flame retardant, and hygiene standards in the food or drink industry or health services; j) ‘two-pack performance coatings’means coatings with the same use as one-performance coatings, but with a second component (e.g. tertiary amines) added prior to application; k) ‘multicoloured coatings’means coatings designed to give a two-tone or multiple-colour effect, directly from the primary application; l) ‘decorative effect coatings’means coatings designed to give special aesthetic effects over specially prepared pre-painted substrates or base coats and subsequently treated with various tools during the drying period.
2.For the purposes of this Directive, ‘vehicle refinishing products’ means products listed in the subcategories below. They are used for the coating of road vehicles as defined in Directive 70/156/EEC, or part of them, carried out as part of vehicle repair, conservation or decoration outside of manufacturing installations. 2.1. Subcategories: a) ‘preparatory and cleaning’ means products designed to remove old coatings and rust, either mechanically or chemically, or to provide a key for new coatings: (i) preparatory products include gunwash (a product designed for cleaning spray-guns and other equipment), paint strippers, degreasers (including anti-static types for plastic) and silicone removers; (ii) ‘precleaner’ means a cleaning product designed for the removal of surface contamination during preparation for and prior to the application of coating materials; b) ‘Bodyfiller/stopper’means heavy-bodied compounds designed to be applied to fill deep surface imperfections prior to the application of the surfacer/filler; c) ‘primer’ means any coating that is designed for application to bare metal or existing finishes to provide corrosion protection prior to application of a primer surfacer: (i) ‘surfacer/filler’ means a coating designed for application immediately prior to the application of topcoat for the purpose of corrosion resistance, to ensure adhesion of the topcoat, and to promote the formation of a uniform surface finish by filling in minor surface imperfections; (ii) ‘general metal primer’ means a coating designed for application as primers, such as adhesion promoters, sealers, surfacers, undercoats, plastic primers, wet-on-wet, non-sand fillers and spray fillers; (iii) ‘wash primer’ means coatings containing at least 0,5 % by weight of phosphoric acid designed to be applied directly to bare metal surfaces to provide corrosion resistance and adhesion; coatings used as weldable primers; and mordant solutions for galvanised and zinc surfaces; d) ‘topcoat’ means any pigmented coating that is designed to be applied either as a single-layer or as a multiple-layer base to provide gloss and durability. It includes all products involved such as base coatings and clear coatings: (i) ‘base coatings’ means pigmented coatings designed to provide colour and any desired optical effects, but not the gloss or surface resistance of the coating system; (ii) ‘clear coating’ means a transparent coating designed to provide the final gloss and resistance properties of the coating system; e) ‘special finishes’means coatings designed for application as topcoats requiring special properties, such as metallic or pearl effect, in a single layer, high-performance solid-colour and clear coats, (e.g. anti-scratch and fluorinated clear- coat), reflective base coat, texture finishes (e.g. hammer), anti-slip, under-body sealers, anti-chip coatings, interior finishes; and aerosols.
Allegato IIANNEX II
A. MAXIMUM VOC CONTENT LIMIT VALUES FOR PAINTS AND VARNISHES Product Subcategory Type Phase I (g/l ( *1 ) ) (from 1.1.2007) Phase II (g/l ( *1 ) ) (from 1.1.2010) a Interior matt walls and ceilings (Gloss < 25@60°) WB 75 30 SB 400 30 b Interior glossy walls and ceilings (Gloss > 25@60°) WB 150 100 SB 400 100 c Exterior walls of mineral substrate WB 75 40 SB 450 430 d Interior/exterior trim and cladding paints for wood and metal WB 150 130 SB 400 300 e Interior/exterior trim varnishes and woodstains, including opaque woodstains WB 150 130 SB 500 400 f Interior and exterior minimal build woodstains WB 150 130 SB 700 700 g Primers WB 50 30 SB 450 350 h Binding primers WB 50 30 SB 750 750 i One-pack performance coatings WB 140 140 SB 600 500 j Two-pack reactive performance coatings for specific end use such as floors WB 140 140 SB 550 500 k Multi-coloured coatings WB 150 100 SB 400 100 l Decorative effect coatings WB 300 200 SB 500 200 ( *1 ) g/l ready to use
B. MAXIMUM VOC CONTENT LIMIT VALUES FOR VEHICLE REFINISHING PRODUCTS Product Subcategory Coatings VOC g/l ( *1 ) (1.1.2007) a Preparatory and cleaning Preparatory 850 Pre-cleaner 200 b Bodyfiller/stopper All types 250 c Primer Surfacer/filler and general (metal) primer 540 Wash primer 780 d Topcoat All types 420 e Special finishes All types 840 ( *1 ) g/l of ready for use product. Except for subcategory (a) any water content of the product ready for use should be discounted.
Allegato IIIANNEX III
METHODS REFERRED TO IN ARTICLE 3(1)
Permitted method for products with VOC content below 15 % by mass where reactive diluents are not present:
Parameter Unit Test Method Date of publication VOC content g/l ISO 11890-2 2006
Permitted methods for products with VOC content equal to or greater than 15 % by mass where reactive diluents are not present:
Parameter Unit Test Method Date of publication VOC content g/l ISO 11890-1 2007 VOC content g/l ISO 11890-2 2006
Permitted method for products with VOC content where reactive diluents are present:
Parameter Unit Test Method Date of publication VOC content g/l ASTMD 2369 2003